Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 86

Страница: 86 / 132

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

Troubleshooting

25 July 2016

Page 4-2

Turntable / Tower

Rotation-

Turntable / Tower Will Not

Stop In The Correct Position.

(Table Does Stop At End Of

Cycle-but In Wrong Position

Turntable end of cycle positioning

counter value is set incorrectly.

Observe the Turntable end of

cycle positioning counter value on

the HMI.

Refer to the factory default settings value

list.

Slow Down Position for Tower /

Turntable Timer is adjusted too

high. Observe the Slow Down

Position for Tower /Turntable

Timer value on the HMI.

Refer to the factory default settings value

list.

Table / Tower preset speeds are

set incorrectly. The table / turnta-

ble is overhauling and the drive

can not stop the load fast enough.

Check the value of the SP-2-SP-3

and SP-4 parameters on the Table

/ Tower VFD. Ensure that they are

set within correct values.

Refer to the factory default settings value

list.

Table / Tower deceleration value

is set incorrectly. The table / turn-

table is overhauling and the drive

can not stop the load fast enough.

Check the value of the DEC

parameter on the Table / Tower

VFD. Ensure that it is set within

the Orion factory default values.

Refer to the factory default settings value

list.

Component failure.

Check error message on the Table / Tower

VFD display.

Refer to the supplied VFD user manual for

error message. Replace if needed.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды