Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 98 / 132

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

Troubleshooting

25 July 2016

Page 4-14

Film Is Breaking Between The

Last Aluminum Roller And The

Load

Pallet greatly overhangs the load.

Observe the load. See if the film break

starts at the corners of the pallet.

Options are:

1. Reduce the film tension at the touch-

screen.

2. Reduce the stretch ratio.

3. Do not wrap the pallet with the load.

Raise the bottom position striker.

Film is damaged.

Observe the edges and sides of the roll for

damage from handling.

Replace improper film with film in good

condition.

Film is wound incorrectly.

Film may be wound incorrectly from the

manufacturer. Look for heavy, raised

stripes along the feed axis of the film. This

is known as "gauge banding".

Replace improper film with film in good

condition.

Stretch chain and / or belt geome-

try is incorrect. Out of alignment

components can cause feed drag.

Remove film carriage cover. Look for

loose chain and / or belt. Look for the belt

pulleys and the chain sprockets to be in

correct alignment.

Adjust as needed by repositioning the

combination sprocket-pulley.

Intermittent break in the cabling

between the carriage and the con-

trol panel.

Observe the film feed during a cycle. If

the film only breaks when the carriage is

in a certain spot in it's travel, then continu-

ity is suspect.

Perform a continuity check on all wiring

pertaining to the carriage while jogging

the carriage up and down. If a break in

continuity occurs, repair or replace the

cable.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды