Primera LP130e Скачать руководство пользователя страница 7

Страница: 7 / 50

Getting Started

Section 2: Getting Started

A. CHOOSING A GOOD LOCATION

• Place the printer on a flat surface in a location with adequate air

circulation to prevent internal heat build-up.

• Do not place the printer near heat sources such as radiators or air

ducts, or in a place subject to direct sun light, excessive dust,

mechanical vibration or shock.

• Allow for adequate clearance in front of the printer to accommodate

the printed label stock as it is leaving the printer to avoid the

possibility of binding or jamming of the label stock.

• Allow for adequate overhead and left side clearance for opening the

top cover to allow easy access to the label stock and maintenance

items. The printer will require

9.5 inches (24 cm) of additional space on the left side to completely

open the cover (total = 26.75 inches or 68 cm). The printer will

require an additional 15.9 inches (40.4 cm) of overhead space to

open the cover (total = 25 inches or 63.5 cm).

B. UNPACKING AND INSPECTION

While unpacking your printer, inspect the carton to ensure that no

damage has occurred during shipping. Make sure that all supplied

accessories are included with your unit. The following items are

included in the supply box:
•  Power Adapter
•  Separate Power Cord
•  USB Cable
•  Software Installer CD
•  Warranty Statement and Registration Card
•  This User's Manual and other printed information

Содержание LP130e


















































Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды

Primera LP130e, Руководство пользователя

Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды