Primera LP130e Скачать руководство пользователя страница 45

Страница: 45 / 50

Maintenance and Troubleshooting

C. CLEANING THE FEED PATH

If smokeless label stock is used the exhaust system will not need to be

replaced every roll of label stock. However, this means that adhesive

may build up on the bottom edge of the Exhaust Duct causing feeding

problems. To clean the Exhaust Duct and feed path use the following

instructions:
1. Remove the Exhaust Duct according to the instructions in Section

6A.

2. Inspect the underside of the Exhaust Duct. Remove any adhesive

with a petroleum-based cleaner such as WD40™ or Goo Gone™.

3. Also inspect the feed area inside the printer. Clean any adhesive

from this area. If it has accumulated on the Exhaust Duct, excess

adhesive may have been deposited along the edges of the label feed

path.

4. When you are finished, replace the Exhaust Duct.

Check for adhesives build

up along the edges.

Feed Path

Содержание LP130e


















































Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды

Primera LP130e, Руководство пользователя

Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды