Primera LP130e Скачать руководство пользователя страница 34

Страница: 34 / 50

Setup the DF-30 Filtration System

B. REPLACE FILTERS

Replace the filters when the “Service

Filters” LED is lit. Some filters are

replaced every time and others are

replaced every other time. The first

time the “Service Filters” LED is lit

you should replace filters 1, 2 and 3

(Kit Part 74481). The next time the

LED is lit you should replace filters 1,2,3,4 and 5 (Kit part 74482). Use

the filter replacement schedule shown later in this section.
To begin, purchase one each of the following kits. After this purchase

only the complete filter kit.

Initial Filter Replacement Kit

Part 74481

Contains Filter 1, 2 and 3. Use this

filter kit the first time you change

filters.

Complete Filter Replacement

Kit Part 74482

Contains Filter 1, 2, 3, 4 and 5.

Use this filter kit for subsequent

filter replacements.

Part/Description

Frequency

74471 - Pre-Filter Element

(pack of 3 – 3 are used each

time)

• Initial Kit 74481

(Contains 1x 3pk)

• Complete Kit 74482

(Contains 2x 3pk)

Replace every

time the Service

Filters LED is lit.

74472 - Large Particle Bag

Filter Element (pack of 2)
• Initial Kit 74481

(Contains 1x)

• Complete Kit 74482

(Contains 2x)

Replace every

time the Service

Filters LED is lit.

RESET

POWER

CORD

REMOTE CONTROL

System ON

Service Motor

Service Filters

Remote / Standby

POWER

CALIBRATION

DF-30

FILTRATION SYSTEM

Warning: Disconnect power cord from wall outlet prior to opening doors and/or servicing unit.

www.primeralabel.com

Содержание LP130e


















































Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды

Primera LP130e, Руководство пользователя

Результаты поиска

Содержание LP130e

Отзывы:

Похожие инструкции для LP130e

Бренды по названию

Популярные бренды