manualshive.com logo in svg

Potterton Paramount four, Руководство по установке, Страница: 98 / 144

Поделиться
Скачать
Potterton Paramount four Скачать руководство пользователя страница 98

First: The first boiler in the addressing works as the lead boiler; for all 

the other boilers the boiler sequence is changed after expiry of the time 

set in prog. no. 3540.

Last: The last boiler in the addressing always remains the last boiler; for 

all other boilers the boiler sequence is changed after expiry of the time 

set in prog. no. 3540.

Leading source (3544)

The setting of the leading generator is only used in combination with the 

fixed sequence of the generator sequence (prog. no. 3540). The generator 

defined as the leading generator is always put into operation first, and 

switched off last. The other generators are switched on and off in the se­

quence of the device address.

Return setpoint min (3560)

If the return temperature drops below the return setpoint set here, the re­

turn maintenance becomes active. The return maintenance enables influ­

ences on the consumers or use of a return controller.

Temp differential min (3590)

This function prevents too high cascade return temperatures and improves 

the switch off behaviour of the cascade. If the temperature difference be­

tween the flow and return sensor is smaller than the minimal temperature 

spread set here, a generator is switched off as early as possible independ­

ently of the set lead strategy. Once the temperature difference is sufficient 

again, the set lead strategy is switched over again.

9.2.13 Solar

Temp diff on (3810) and Temp diff off (3811)

1 / 0 On / off collector pump

T Temperature

T1 Temp diff on

T0 Temp diff off

TK Collector temperature

TL Charging temperature min buffer storage tank / swimming pool

TS Storage tank temperature

t Time

The switching-on and switching-off point of the collector pump is set with 

these functions. Basis is the temperature difference between collector 

temperature and storage temperature.

Charg temp min HW st tank (3812)

In addition to the temperature difference, reaching a certain minimum col­

lector temperature is necessary for the storage charging process.

Temp diff on buffer (3813),Temp diff off buffer (3814) 

andCharging temp min buffer (3815)

The switching-on and switching-off point of the collector pump is set with 

these functions. Basis is the temperature difference between collector 

temperature and storage temperature of the buffer storage tank.
In addition to the temperature difference, reaching a certain minimum col­

lector temperature is necessary for the buffer storage charging process.

Temp diff on swi pool (3816) andTemp diff off swi pool (3817)

The solar circuit pump starts or stops if the difference between the solar 

collector temperature and the swimming pool temperature is exceeded or 

undershot.

Charging temp min swi pool (3818)

Temperatures that the collector must have at the least in order to begin 

charging a swimming pool.

Fig.30 Charging control /schematic)

TK

T1

T2

TL

1

0

TS

RA-0000080

T

t

9  Settings

98

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Содержание Paramount four

















































































































































Отзывы:

Нет отзывов