Potterton Paramount four Скачать руководство пользователя страница 126

Страница: 126 / 144

End user (Eu)

Commissioning, Engineer (menu

Status)

Charg el imm heater

El charg, emergency mode

El charg, source protection

Electric charging defrost

Electric charging, forced

Electric charging, substitute

Charging restricted

Charging locked

Restricted, HW priority

Charging active

Forced charging active

Partial charging active

Recooling active

Recooling via collector

Recooling via HW/CHs

Charged

Charged, max st tank temp

Charged, max charging temp

Charged, forced temp

Charged, required temp

Part charged, required temp

Charged, min charging temp

Cold

No request

Tab.34 Status table swimming pool

The following messages are possible under Swimming pool:

End user (Eu)

Commissioning, Engineer (menu

Status)

Manual control active

Fault

Heating mode restricted

Heating mode source

Heated, max swi pool temp

Heated

Heated, setpoint solar

Heated, setpoint source

Heating mode

Heating mode solar off

Heating mode source off

Cold

9.2.24 Diagnostics cascade/heat generation/consumers

Diagnostics cascade/heat generation/consumers (8100-9058)

Displays of different setpoint and actual values, relay switching statuses

and counter statuses for diagnosis purposes.

Gas energy

There are 6 energy meters available, comprising the estimated gas energy

used with the aid of the fan speed and a linear approximation of the actual

burner output. The energy meters must be switched on and off using

prog.no. 2550. The results can be corrected under prog.no. 2551.

2 overall meters can be reset on the engineer level:

Prog.no. 8378: Overall gas energy heating

Prog.no. 8379: Overall gas energy DHW

The end consumer can reset 2 meters:

9 Settings

126

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Содержание Paramount four

















































































































































Результаты поиска

Содержание Paramount four

Отзывы:

Potterton Paramount four, Руководство по установке, Страница: 126 / 144

Результаты поиска

Содержание Paramount four

Отзывы: