manualshive.com logo in svg

Potterton Paramount four, Руководство по установке, Страница: 105 / 144

Поделиться
Скачать
Potterton Paramount four Скачать руководство пользователя страница 105

Note

The automatic push only works when DHW operating mode is set.

Excess heat draw (5085)

Excess heat draw-off can be triggered by the following functions: Maxi­

mum storage tank temperature, automatic push, heating priority time push, 

excess heat draw-off, active inputs H1, H2, H3 or EX2, storage tank re­

verse cooling, solid boiler excess heat draw-off. If an excess temperature 

discharge is activated, the excess energy can be dissipated through the 

central heating drawing off heat. This can be separately set for each heat­

ing circuit.

With buffer (5090)

No: The DHW storage tank is supplied directly by the boiler.

Yes: The DHW storage tank is supplied by the buffer storage tank.

With prim contr/system pump (5092)

No: The DHW storage tank is supplied without primary controller/feed 

pump.

Yes: The DHW cylinder is supplied from the primary controller on/by the 

feed pump.

With solar integration (5093)

This function determines whether the DHW cylinder should be heated by 

solar energy.

Pump speed min (5101) andPump speed max (5102)

Setting of the minimum and maximum speed of the storage tank charging 

pump in percent.

Speed Xp (5103)

The P-band Xp defines the amplification of the controller. A smaller Xp val­

ue leads to a higher actuation of the charging pump with equal control dif­

ference.

Speed Tn (5104)

The reset time Tn determines the reaction speed of the controller when 

compensating for remaining controller differences. A shorter reset time Tn 

leads to faster compensating.

Speed Tv (5105)

The preholding time Tv determines how long a spontaneous change of the 

control difference continues to have an effect. A short time only influences 

the control variable only for a short time.

Transfer strategy (5130)

The transfer is always allowed or to the set DHW release times.

Interm circ boost recharging (5139)

Setpoint boost for charging setpoint on charging sensor B36 with recharg­

ing.

Intermediate circuit boost (5140)

Setpoint boost for charging setpoint on charging sensor B36 with full 

charging.

Excess interm circ temp max (5141)

With this parameter the end criterion of a full charging during control is 

specified on the charging sensor B36. If the contents of the stratification 

cylinder is charged to the bottom, the temperature increases on the charg­

ing sensor

Flow setp compensation delay (5142)

The filter time for the setpoint lead is set here.

9  Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

105

Содержание Paramount four

















































































































































Отзывы:

Нет отзывов