Potterton Paramount four Скачать руководство пользователя страница 117

Страница: 117 / 144

control goes in a parameterization position. As soon as parameters are

transferred, the LMS control must be unlocked transmission has ended.

Fault 183 parameterization is displayed.

Writing on stick: Starts writing the data from the LMS control to the stick.

This operation is only possible with WRITE sticks. The data is written in

to the previously set data set. Before writing of the data begins, it is

checked whether the stick has sufficient capacity for the data and that

the respective customer number is correct. The textWriting on stick re

mains until the operation is completed or a fault occurs.

PStick progress (7253)

The read or write progress is displayed as a percentage. If no operation is

active or a fault occurs, 0% is displayed.

PStick status (7254)

No stick: The LMS control has not detected a stick (the stick may not be

inserted).

Stick ready: Basic condition, stick is detected, no action active, no error

present.

Writing on stick: Data is copied (backup) from the LMS control to the

stick.

Reading from stick: Data is transferred from the stick to the LMS control.

EMC test active: Special function for EMC tests in the lab. A special

compiler switch must be set for this.

Writing error: An error occurred when copying the data from the LMS

control to the stick. The operation was aborted.

Reading error: An error occurred when copying the data from the stick to

the LMS control.. The operation was aborted. The control LMS is locked.

Status change to read lock.

Incompatible data set: Data set does not match LMS control. Compati

bility conditions are not met. The data set can not be imported.

Wrong stick type: Stick type does not match selected action. E.g. read

ing from write stick or writing to read stick is not possible.

Stick format error: Incorrect customer number on the stick or data format

on the stick is unknown and cannot be evaluated by the LMS control.

Check data set: During transmission of a data set from the stick to the

LMS control a problem occurred, but it did not lead to an abort.

Data set disabled: The data set may not be transferred into the LMS

control (read protected).

Reading disabled: The parameterization position is in the

ABORT

state.

Only limited actions are possible to cancel the parameterization position.

9.2.21 Configuration of extension modules

Function extension module 1 (7300), Function extension

module 2 (7375)

When a function is selected, the inputs and outputs are occupied on the

extension module with the functions according to the following table:

Connection ter

minal on module

QX21 QX22 QX23 BX2

BX2

H2/H21 H22

Multi-functional

Heating circuit 1

Heating circuit 2

B12

Heating circuit 3

Y11

Y12

Q20

B14

Solar DHW

B31

Primary control/

system pump

Y19

Y20

Q14

B15

* Freely selectable in QX.../ BX...

FS = DHW flow switch; AVS75.390 = H2; AVS75.370 = H21

9 Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

117

Содержание Paramount four

















































































































































Результаты поиска

Содержание Paramount four

Отзывы:

Potterton Paramount four, Руководство по установке, Страница: 117 / 144

Результаты поиска

Содержание Paramount four

Отзывы: