manualshive.com logo in svg

Potterton Paramount four, Руководство по установке, Страница: 88 / 144

Поделиться
Скачать
Potterton Paramount four Скачать руководство пользователя страница 88

For more information, see

Time constant building (6110), page 111

Reduced setp increase start (800, 1090, 1390) and Reduced 

setp increase end (801, 1101, 1401)

TA1 Reduced setpoint increase start

TA2 Reduced setpoint increase end

TK Comfort setpoint

TR Room temperature reduced setpoint

TAg Outside temperature mixed

When only a small heating output is required to cover demand, the re­

duced room setpoint can be increased in the case of cold outside temper­

atures. This increase is subject to outside temperature. The lower the out­

side temperature, the higher the reduced room temperature setpoint will 

be increased. The start and end of the increase can be selected. Between 

these two points there is a linear increase of the "reduced setpoint" up to 

the "comfort setpoint".

Continuous pump operation (809, 1109, 1409)

This function is used to suppress the pump switching off during the quick 

reduction and when the room setpoint is reached (room thermostat, room 

sensor or room model).

No: the heating circuit pump /boiler pump can be switched off by quick 

reduction or reaching the room set point.

Yes: the heating circuit pump/boiler pump remains switched on even 

during the quick reduction and after the room setpoint has been 

reached.

Overtemp protect pump circ (820, 1120, 1420)

This function prevents overheating of the pump heating circuit by switching 

the pump on and off, if the flow temperature is higher than the flow tem­

perature required according to the heating curve (e.g. in case of higher re­

quests from other consumers).

Mixing valve boost (830, 1130, 1430)

The heat request of the mixed heating circuit to the heat source is raised 

above the value set here. This boost is intended to correct temperature 

fluctuations to be able to be compensated with the mixer controller.

Actuator running time (834, 941, 1134)

Setting the actuator running time of the mixing valve used.
For mixing circuits, a kick-start of the mixer drive is carried out after a 

pump kick-start (pump is OFF). In this case, the mixer is controlled in di­

rection OPEN and CLOSED.
The time of activation in direction OPEN corresponds to the drive running 

time.

Floor curing function (850, 1150, 1450)

X Start day

Fh Functional heating

Ch Curing heating

The floor curing function serves controlled drying out of screed floors

Off: The function is switched off.

Functional heating: Part 1 of the temperature profile is run automatically.

Curing heating: Part 2 of the temperature profile is run automatically.

Functional/curing heating: The whole temperature profile is run automat­

ically.

Manually: Manual control to the screed setpoint.

Fig.25 Reduced setpoint increase

RA-0000071

-15

-5

TAg

TA1

TA2

TK

TR

Fig.26 Temperature profile of the floor cur­

ing function

X

Fh

Bh

Fh + Bh

RA-0000072

9  Settings

88

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Содержание Paramount four

















































































































































Отзывы:

Нет отзывов