manualshive.com logo in svg

Potterton Paramount four, Руководство по установке, Страница: 94 / 144

Поделиться
Скачать
Potterton Paramount four Скачать руководство пользователя страница 94

9.2.11 Boiler

Release below outside temp (2203)

The boiler is only put into operation if the mixed outside temperature is be­

low the threshold set here. The switching difference is 0.5°C.

Full charging buffer (2208)

Under prog. no. 4810 (full charging buffer storage tank) is selected, wheth­

er and when the buffer storage tank is fully charged despite automatic 

generator lock. Under prog.no. 2203 it is set whether the boiler takes part 

in the full charging or not.

Off: The boiler does not take part in the full charging of the buffer stor­

age tank.

On: The boiler takes part in the full charging of the buffer storage tank.

For more information, see

Full charging (4810), page 102

Setpoint min (2210) andSetpoint max (2212)

As a protection function the boiler temperature setpoint can be limited be­

low by the minimum setpoint (prog.no. 2210) and above by the maximum 

setpoint (prog.no. 2212).

Setpoint manual control (2214)

Temperature to which the boiler is controlled in manual control mode.

For more information, see

Manual control (7140), page 116

Burner running time min (2241)

Here, the period following the commissioning of the burner is selected dur­

ing which the shutdown differential is increased by 50%. However, this 

setting cannot guarantee that the burner remains operational for the selec­

ted period.

Burner off time min (2243)

The boiler minimum pause time only takes effect between heating require­

ments coming following in sequence. The boiler minimum pause time 

blocks the boiler for a set time.

SD burner off time (2245)

When a switching difference is exceeded,Burner off time min (prog. no. 

2243) is aborted. The boiler starts despite pausing time.

Pump overrun time (2250) andPump overr time after HW 

(2253)

The delay times of the pumps are controlled according to heating mode or 

drinking water mode.

Boiler pump on heat gen lock (2301)

Stop of boiler pump in case of activated manual heat generation lock (e.g. 

via H1).

Off: Switching off not activated

On: Switching off activated

Impact heat generation lock (2305)

This parameter is used to set whether the heat generator lock should be 

effective only for heating requests or also for DHW requests.

Heating mode only: Only heating requests are locked. DHW requests 

are still operated.

Heating and HW mode: All heating and DHW requests are locked.

Temp differential max (2316)

When the pump reaches the maximum speed with the setting temperature 

rise nominal, the temperature difference increases via the boiler. The val­

9  Settings

94

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Содержание Paramount four

















































































































































Отзывы:

Нет отзывов