Potterton Paramount four Скачать руководство пользователя страница 53

Страница: 53 / 144

Over 2.5 bar: Do not put the gas condensing boiler into operation. Drain

the water.

Caution

Observe the maximum permissible system pressure.

Check that there is a drip pan below the discharge pipe from the safety

valve. In the case of overpressure, it collects heating water as it is expel

led.

8.5 Checking the domestic water storage tank

Where systems work with a domestic water storage tank, this must always

be filled with water. In addition, it must be possible for cold water to enter.

8.6 Preparing start-up

This section describes which general work has to be done to switch the

boiler on.

1. Switch on the heating emergency switch.

2. Open the gas tap.

3. Open the disconnector valves.

4. Open the domestic water supply.

5. Open the front panel cover and switch the ON/OFF switch on the

front panel of the boiler to on.

The Paramount four can be commissioned using its standard values with

out any further settings. For information regarding setting e.g. an individual

time program, please see the

Operation

chapter.

For more information, see

Changing parameters, page 51

8.7 Setting the heating mode

The operating mode key for heating mode enables a changeover between

the various heating operating modes. The selected setting is marked with

a bar underneath the operating mode symbol.

Automatic mode

Heating mode according to time program

Temperature setpoints or according to time program

Protection functions (plant frost protection, overheating protection) acti

vated

Automatic summer/winter changeover (automatic switching over be

tween heating and summer operation from a certain outside temperature

onwards)

Automatic day heating limit (automatic changeover between heating and

summer operation, if outside temperature exceeds the room setpoint

value)

Continuous mode or

Heating mode without time program

Protection functions activated

Automatic summer/winter changeover is not activated

Automatic day heating limit is not activated

Protection mode

No heating operation

Temperature according to frost protection setpoint

Protection functions activated

A-0

xxxxxxxxxxxxxx

8 Operation

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

Содержание Paramount four

















































































































































Результаты поиска

Содержание Paramount four

Отзывы:

Potterton Paramount four, Руководство по установке, Страница: 53 / 144

Результаты поиска

Содержание Paramount four

Отзывы: