manualshive.com logo in svg

Potterton Paramount four, Руководство по установке, Страница: 41 / 144

Поделиться
Скачать
Potterton Paramount four Скачать руководство пользователя страница 41

U

Below windows or openings on pitched roofs.

2000 mm

(1) In addition, the terminal should be no nearer than 150 mm to an opening in the building fabric formed for the purpose of accommodating 

a built-in element such as a window frame.

(2) Only one 25 mm clearance is allowed per installation. If one of the dimensions D, E, F, G or H is 25 mm then the remainder MUST be as 

shown in brackets, in accordance with BS 5440-1

6.3.6  Chimneys already in use

If a chimney used before for oil or solid fuel-fired boilers is used as a shaft 

for installation of a concentric exhaust gas pipeline, the chimney must be 

thoroughly cleaned first by a specialist.

Note

The concentric flue gas pipe must run straight in the duct.

Height above the roof

With regard to the minimum height above the roof, country-

specific regulations regarding chimneys and flue gas systems 

are applicable.

6.3.7  Cleaning and inspection openings

Danger

Clean exhaust gas pipelines!

It should be possible to clean the flue gas pipes and inspect their 

free cross-section and leakproofness.

At least one cleaning and inspection opening must be installed in the in­

stallation room of the Paramount four.
Exhaust gas pipes in buildings, which cannot be cleaned or inspected from 

their port side must have an additional cleaning port in the upper part of 

the exhaust system or above the roof.
The exhaust gas pipelines at the outer wall must have at least one clean­

ing opening in the lower part of the exhaust gas facility. For exhaust gas 

facilities with building heights of < 15.00 m in the vertical section, a pipe­

line length of < 2,00 m in the horizontal section and a maximum pipeline 

diameter of 150 mm with a maximum deflection (except for deflection di­

rectly at the boiler and in the shaft) one cleaning and inspection opening in 

the installation room of the Paramount four is sufficient.
The ducts for exhaust gas facilities must not have any openings other than 

the necessary cleaning and inspection ports as well as openings for back 

ventilation of the exhaust gas pipe.

6.4  Electrical connections

6.4.1  Electrical connection (general)

Danger

Danger to life through incorrect work!

All electrical work in connection with the installation may only be 

carried out by a trained electrician.

Mains supply AC 230 V +6% -10%, 50 Hz

In UK follow the relevant regulations.
The electrical connection should be made with correct and non-reversible 

polarity. In Germany the connection can be executed as an accessible 

plug and socket connection with non-reversible polarity or as a fixed con­

nection. In all other countries, a fixed connection must be provided.
For the power supply, use the power cable attached to the boiler or cable 
types H05VV-F 3 x 1 mm

2

 or 3 x 1.5 mm

2

. The earthing cable must be lon­

ger at the connection in order to guarantee that this connection is the last 

cable to rupture in the event of a hazard.

6  Installation

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

41

Содержание Paramount four

















































































































































Отзывы:

Нет отзывов