background image

Oct-18-700

 

Operation

 

Page 29 of 34

 

Section 8 - Emergency operation

 

 

Operating safely

 

 
Should the occupant of the platform suffer injury while aloft, disabling that person from 
operating the platform controls, the platform may be lowered by means of the overriding 
lower controls. 
 

Danger

 

 

Before attempting to lower the platform with the lower control, for the protection of the 
ground personnel, it must first be determined that the vehicle is not energized.  Death 
or serious injury can result from contact with equipment that has become electrically 
energized. 

 

 
Upon determining that it is safe to touch the vehicle, the lower controls may be used for 
booms' movement. 
 

  From the pedestal controls, selecting and holding the "Override" position with the 

toggle switch at the pedestal door, permits operation of the aerial device from the 
lower hydraulic controls. 

 

Emergency lowering DC pump 

 

If a situation arises that the machine cannot be operated due to a 

loss of hydraulic 

power,

 such as engine or pump failure, the emergency lowering DC pump can be used 

to lower the main boom. 

 
The 12-volt DC battery operated pump is designed for use in case the vehicle engine or 
power system fails.  The emergency lowering DC pump may be operated from the platform 
or the pedestal controls. The pump is located near the reservoir and power is supplied to 
the pump from the vehicle battery.  The capacity of this pump is dependent on the capacity 
of the battery. 
 
The emergency lowering DC pump system has been designed to allow for lowering the 
booms to the ground for operator rescue, but may not allow for complete storage of the 
booms. 
 

 

Attention

 

 

The DC pump is intended for emergency lowering use only.  Do not run for over three 
(3) minutes continuously.  Damage to the pump or motor can result. 

 

 

Содержание Line Runner 700-40



































Отзывы: