background image

Oct-18-700

 

Operation

 

Page 25 of 34

 

Personnel Platform

 

 
This aerial device is equipped with an aluminum platform. 
 

 

Danger

 

 

The aluminum platform at the boom tip area does not provide any protection against 
electrical continuity.  It cannot protect against any contact with energized lines 

 

 

Caution

 

 

Use care when getting on and off the unit and/or when entering and exiting the platform 
to avoid slipping or falling. Maintain three points contact when getting on and off. 

 
The personnel platform capacity is found on the serial number placard.  
 
The "Platform Capacity” indicated on the placard installed at the upper controls station is 
the total weight allowed as platform contents:  Operator(s), liner(s), tools and equipment. 
 
All platform occupant(s) of this aerial device must always wear a certified CSA or OSHA 
approved full body harness attached to a lanyard while operating the unit from the 
platform.  The lanyard must be secured to the lanyard anchor (D-ring) near or on the 
platform. 
 
All platform occupants must always wear appropriate personal protective devices at all 
times (i.e. hard hats, safety shoes or boots; safety glasses, work gloves). 
 
Always stand firmly and keep both feet on the floor of the platform. Never sit, stand, or 
climb on the edge of the platform. Never place any item or equipment in the platform for 
the purpose of increasing work height (planks, ladders, step stools). Never try to climb 
down from the platform, if the platform is not down to the ground. Make sure the platform 
floor is clear of debris, tools and other equipment that could make the operator unstable 
and prevent from having both feet on the floor during the operation. 
 
 

Attachment for fall protection 

 
Depending on the model and options installed on the unit, the attachment for fall protection 
(D-ring attachment) can be installed in different locations, but it is always located near the 
platform mounting bracket.  The D-ring is rated for one person only. 

 
 

 

Содержание Line Runner 700-40



































Отзывы: