Porsche 928 S 1984 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 109

Porsche 928 S 1984 Скачать руководство пользователя страница 65

Exercise Extreme Caution when

Working under the Engine Hood

The engine compartment of any motor ve-
hicle is a potentially hazardous area. If you

are not fully familiar with proper repair pro-
cedures, do not attempt the adjustments
described on the following pages. This cau-
tion applies to the entire vehicle.

• Before working on any part in the en-

gine compartment, turn the engine off
and let it cool down sufficiently. Hot en-
gine compartment components can burn
skin on contact.

• Even after the engine has stopped, the

radiator fan may continue running until

temperature of the coolant has dropped
to a certain level. Therefore, never touch
the fan blades as they will rotate spon-
taneously when the thermostat turns the
fan on, even with ignition off.

• Be alert and cautious around engine at

all times while the engine is running.

• If work has to be done with the engine

running, always set the parking brake,
and make sure the shift lever is in either
Neutral or Park.

• Exercise extreme caution to prevent

neckties, jewelry or long hair from get-

ting caught in the fan blades, the drive

belts, or any other moving engine parts.

• Your Porsche is equipped with a tran-

sistorized ignition system with breaker-
less distributor. When the ignition is on,
high voltage is present in all wires con-
nected with the ignition system; there-
fore, exercise extreme caution when
working on any part of the engine while

the ignition is on or the engine is running.

• Always support your car with safety

stands if it is necessary to work under-

neath the car. The jack supplied with the
car is not adequate for this purpose.

• When working underneath the car with-

out safety stands but with the wheels on
the ground, make sure the car is on level
ground, that the wheels are blocked, and
that the engine cannot be started.
REMOVE THE IGNITION KEY.

• Do not smoke or allow an open flame

around the battery or gasoline.

• Keep a fire extinguisher in close reach.

• Incomplete or improper servicing may

cause problems in the operation of the
car. If in doubt about any servicing, have
it done by your authorized Porsche deal-
er or any other properly equipped and
qualified workshop.

• Improper maintenance during the war-

ranty period may affect your warranty
coverage.

62

«
...
63
64
65
66
67
...
»

Содержание 928 S 1984














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды