Porsche 928 S 1984 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 109

Porsche 928 S 1984 Скачать руководство пользователя страница 41

Central warning light system

This electronic warning system monitors the

most important functions of your Porsche for
increased safety and reliability of performance.
Should a problem arise, the center warning
system will inform you immediately.

The central warning light is located in the cen-
ter of the instrument cluster. The individual
warning lights are divided between the two
combination instruments.

When the ignition is turned on, the central
warning light and all individual warning lights
will light up for a bulb check. If the engine oil
level is too low the central warning light will

flash. (Lack of engine oil can, in comparison
with all other functions, only be checked with

the engine turned off and with the vehicle level.)
As soon as the engine is started, the lights
should go out. The STOP LAMP light will go
out after the brake pedal has been depressed.
The PARK BRAKE light will go out as soon as
the parking brake lever is fully released.

Should a problem arise, the central warning
light will light up or flash, together with the re-
spective individual warning light.

The control function of the central warning light
system is divided into two major groups:

Group " A " - engine oil pressure

- engine oil level
- brake circuit (pressure) failure
- brake fluid level

Any malfunction reported by the system
must be corrected immediately.

Group " B " - brake wear (pads) indicator

- parking brake
- coolant level
- coolant temperature
- fuel reserve level
- windshield and headlight

washer (where applicable)
fluid level

- stop lamps
- tail lamps

Any malfunction reported by the system should

be corrected as soon as possible.

Reset button (white arrow)

By pressing this button, you can turn off the

central warning light for group " B " related
problems. The individual warning light in the
respective combination instrument will remain
on as a reminder to have the fault corrected.

The reset button does not apply to group
"A" related problems. Both central and indi-
vidual warning light swill continue to flash be-
cause an immediate remedy of the problem is
necessary.

Central door locking button

With the ignition key in Pos. " 1 " or " 2 " both
doors can be locked or unlocked by pressing

the central locking button.

See "Central door locking system".

38

«
...
39
40
41
42
43
...
»

Содержание 928 S 1984














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды