Porsche 928 S 1984 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 109

Porsche 928 S 1984 Скачать руководство пользователя страница 20

Rear view mirrors

Adjust the outside and inside mirrors be-
fore driving off. It is important for safe driv-

ing that you have good vision to the rear.

Do not put decals or other signs on the win-
dows that may interfere with the driver's
vision.

Inside day-night mirror

You can adjust the day-night mirror from clear
daylight visibility to non-glare visibility at night,
by moving the lever at the bottom of the mirror
forward or rearward.

Heated outside mirrors with remote control

When the rear window defogger/defroster is
switched on, the outside mirrors are also heat-
ed electrically. The outside mirrors can be ad-
justed from the inside by remote control when
the ignition is turned on. The control switch is
located next to the side window vents in the
armrest.

The electrically heated outside mirror for the
passenger side can be adjusted with the same
control switch, by pressing the rocker switch
beside the adjuster switch into the appropriate
position.

If necessary, the outside mirrors can also be

adjusted manually.

19

«
...
18
19
20
21
22
...
»

Содержание 928 S 1984














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды