Porsche 928 S 1984 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 109

Porsche 928 S 1984 Скачать руководство пользователя страница 22

Inertia reel retractor

The combination lap/shoulder belt with inertia
reel locking mechanism adjusts automatically
to your size and movements as long as the pull
on the belt is slow.

Rapid deceleration during hard braking or a

collision locks the belt. The belt will also lock
when you drive up or down a steep hill or in a
sharp curve.

• To fasten, grasp latch and pull belt in contin-

uous slow motion across your chest and lap.

• Insert latch into buckle on inboard side of

seat. Push down until it is securely locked
with an audible click. Pull belt to check.

• Pull shoulder section to make sure belt fits

snugly across the hips.

• Belts should fit snugly across the pelvis and

chest. Make sure any slack is wound on the
retractor.

• To unfasten belt, push in release button on

buckle. Belt will spring out of buckle.

• To release a locked belt, lean back to take

the body pressure off the belt.

• To store lap/shoulder belt, allow belt to wind

up on retractor as you guide latch to its

stowed position on doorpost.

Lap belts for rear seats

The automatic retractor will lock the rear seat
lap belt when your passenger has buckled up,
and the remaining slack has retracted.
The belt can only be pulled out after it is fully
retracted.

• To fasten lap belt, grasp latch on outboard

side of seat and slowly pull across the pel-
vis. Insert latch into buckle on inboard side
of seat and push down until it is securely
locked with an audible click. Pull belt to
check. To unfasten belt, push in release but-
ton on the buckle.

• To store belt, allow belt to wind up as you

guide latch to retractor.

21

«
...
20
21
22
23
24
...
»

Содержание 928 S 1984














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды