Porsche 928 S 1984 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 109

Porsche 928 S 1984 Скачать руководство пользователя страница 44

Side window vents

The air outlets in the armrests permit adjust

ment of air flow either sideways or up and

down. Open and close vents with small side
lever.

A vents closed

Β vents open

Center air vents

The center air vents direct air flow to the pas
senger compartment and are adjustable either
sideways or up and down. Open and close
vents with small side lever.

Automatic climate control

This system automatically controls the air flow
distribution and the temperature level inside
the car according to the occupants wishes.
The distribution and mixture of cool and warm
air is electrically regulated and kept constant,
regardless of weather conditions.

Individual controls

Fan speed control - rotary switch knob

The

air volume

is controlled by a 4-speed fan.

When the ignition is turned on, the fan auto
matically operates at low speed, even with the
switch in 0 position. By turning the knob clock
wise, fan speeds 1 - 4 can be selected to in
crease the air volume.

Temperature control - upper lever

Move lever to desired temperature setting.

Program control - lower lever

Climate control system and fan motor
off.
Air flow distribution only through side
window and center air vents.
Air flow distribution through windshield
and footwell outlets. The side and cen

ter vents can be opened optionally.
Air flow distribution through windshield
outlets. The side and center vents can

be opened optionally.

Air flow distribution through footwell out

lets. The side and center vents can be
opened optionally.

Automatic air flow distribution for heated
air through windshield outlets and open
side window vents. Heating system and
fan motor are automatically switched
on maximum output and high speed for

fast defrosting or defogging. At temper

atures above 32° F/0°C the air condi

tioner compressor runs automatically.

41

«
...
42
43
44
45
46
...
»

Содержание 928 S 1984














































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды