Poettinger NOVACAT 225 H Скачать руководство пользователя

Страница: 8 / 54

(348) TRANSPORTSTELLUNG 0400-GB

- 8 -

Attention!

Take care with transport positions 1, 2, 3.

Before swivelling the cutter bar up, turn

off the drive and wait for the mower discs
to come to a complete standstill.

NOTE:

The implement has been so designed that the mower
unit is positioned as close as possible to the tractor.
This has important advantages for both mowing and
transporting operations.

• The implements´s centre of gravity lies close to the

tractor and through this

- less supporting structure load

- less load alleviation of the steering axle when

transporting

- better cutter bar ground adaption when mowing

• The mower bar can be swivelled into 3 different positions

for transportation.

Safety Precaution!

see supplement-

A1 points 7.), 8c.

- 8h.)

Changing from

working position

to transport

position is only

to be carried out

on even, firm

ground.

Never let mowing

mechanism run
with the mower

raised.

Swinging cutter bar down

- Make sure that

swivel area is free
and that nobody
is standing in the
danger area.

Conversion from working to transport position

Conversion from transport to working position

- Gently raise cutter bar with swivel cylinder so that hook

(13) can be released.

- Release hook (13) by pulling on the rope (S2).

- Lower cutter bar hydraulically.

Up to 2003 model

From 2004 model

48/00/20

TRANSPORT- AND WORKING POSITION

Содержание NOVACAT 225 H























































Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды

Poettinger NOVACAT 225 H, Руководство оператора

Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды