Poettinger NOVACAT 225 H Скачать руководство пользователя

Страница: 11 / 54

0400_GB-Abbauen_348

- 11 -

Dismount implement from tractor

Attention!

•

Always

park implement

steadfast

•

Use

support stand -

otherwise danger

of tipping

• Danger of injury

from crushing

and shearing

sections in

the area of the

support stand

• Follow

the

instructions on

the following

page also.

Instructions

The

lever

13b

is a safety device. It should not be

changed in its form and functions.

The lever is so constructed that it will not spring out from
the bolt position (

13b, 13a

) during hydraulically slewing

of the mowing bar. The lever is thus only damaged
(deformed) but remains in the bolt position.

This has been arranged by the manufacturer – for safety
reasons.

•

Do not operate the hydraulic cylinder to
slew across the mowing bar when the lever
is in the bolt position

•

Exchange damaged levers immediately for
new ones.

Important!

Keep to the order of operation

1. Shift servo to floating position so that no residual air

pressure remains in hydraulic lines.

2. Let bolt (13a) rest in the hook.

- Pull the rope (S2)

- Lower mounting frame with lifting gear until the bolt

(13a) rests in the hook.

3. Move the lever (13b) to the locking position

Doing this secures the bolt (13a) in the hook

This safeguard is important!

Otherwise the danger exists that the

mounting frame of the cutter bar could
swivel up in jerks and jolts when uncoupling
the lower link

4. Bring support stand (14) into support position and

secure with linch pin

5. Lower lifting gear far enough so that implement stands

on support stand on the ground

6. Dismount implement from tractor (15)

- Uncouple drive shaft.

- Uncouple hydraulic lines.

- Remove rope from tractor cabin.

Up to 2003 model

From 2004 model

495-733a

13a

13b

13a

13b

DISMOUNT AND PARKING

Содержание NOVACAT 225 H























































Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды

Poettinger NOVACAT 225 H, Руководство оператора

Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды