Poettinger NOVACAT 225 H Скачать руководство пользователя

Страница: 10 / 54

(348) TRANSPORTSTELLUNG 0400-GB

- 10 -

TRANSPORT- AND WORKING POSITION

Transport position - 3

Cutter bar to the rear and swivelled up (approx.

90°).

1. Swivel mower bar back as described in

"Transport

Position - 2"

2. Move mower bar into vertical position as described in

"Transport Position - 1"

- Secure cutter bar with hook (13).

3. Before driving on roads always check correct

locking!

- Connect lighting and raise implement for transport.

- Before leaving the tractor lower cutter bar to ground!

Transport position - 4

Cutter bar laterally swivelled up (approx. 20°)

- this position upwards is limited by a stop buffer.

• only for turning manoeuvres in the field.

• do not use on roads or public thoroughfares!

Reducing the Total Height

Before converting to transport position

• The external guard plate (10) can be swivelled in to

reduce the total height (- 30 cm) when in the transport
position.

Note:

For safety reasons

the mower

disks must be

at a complete

standstill before

swivelling the

guard plate.

02/00/06

TD48/00/21

02/00/07

Содержание NOVACAT 225 H























































Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды

Poettinger NOVACAT 225 H, Руководство оператора

Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды