Poettinger NOVACAT 225 H Скачать руководство пользователя

Страница: 9 / 54

(348) TRANSPORTSTELLUNG 0400-GB

- 9 -

TRANSPORT- AND WORKING POSITION

Transport position - 2

Mower bar swivelled back.

Cutter bar o the rear and swivelled up until it stops

(approx. 20°)

Note:

Only short trips at low speed may be carried

out in this position

Variant 1:

Without hydraulic slewing mechanism

- Lower cutter bar to ground.

- Release bolt (40) by pulling

on the rope (S1) and move
forwards with the tractor.

In doing so, the cutter bar

swivels back so far until
the bolt (40) is locked into
position.

- Raise the implement using

the tractor's lifting gear.

Variant 2:

With hydraulic slewing mechanism

An additional double-action hydraulic connection is
necessary on the tractor.

A hydraulic unit is installed instead of a mechanical slewing
unit (with bolts 40). See chapter “Collision Safety”.

- Raise cutter baractuate

single-action control valve (ST)

- Swivel cutter bar to the rearactuate

double-action control valve (ST)

Transport position - 1

Mower bar only swivelled up at the side.

- Pull on rope (S2) and simultaneously actuate servo-

valve (ST).

- Gradually move cutter bar into vertical position and

release rope (S2).

- Secure cutter bar with hook (13).

- Servo-valve (ST) to O

position

Tips for transportation:

Do not move the servo-valve (ST) to the ”float” position.

The hook (13) will become very worn.

- Before driving on roads always check correct

locking!

- Connect lighting and raise implement for transport.

- Before leaving the tractor lower cutter bar to ground!

Ensure a sufficient gap (X1) !

Incombination with larger tractor types, it couldhappen
that there is insufficient gap
to the mud guard or tyre

(X1)

which could then cause

a cxollision with the cutter
bar.

If this is the case, this

transport position must not
be used.

It is possible to try to move
the cutter bar further to the
right.

- Insert lower linkage bolts

accordingly (see instructions in the supplement to
this manual)

- However the total sidth must not exeed a

maximum

of 3 m

Attention!

Important

instructions

in the chapter

entitled ”Parking

the implement”

02/00/05

02/00/04

02/00/08

max. 3 m

Содержание NOVACAT 225 H























































Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды

Poettinger NOVACAT 225 H, Руководство оператора

Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды