Poettinger NOVACAT 225 H Скачать руководство пользователя

Страница: 12 / 54

0400_GB-Abbauen_348

- 12 -

DISMOUNT AND PARKING

Support Stand

The support stand can be pinned in 4 positions

Positions 1, 2, 3:

when parking the implement

Position 4:

For transport and operating positions

Parking the implement on the support stand

Any position (1, 2, 3) can be chosen which enables

lifting gear to be uncoupled without problems.

Nevertheless, should a problem arise when

uncoupling the lifting gear

- park the implement on

flat, firm ground

- turn the lower link

adjusting spindle (15)
far enough so that
the lower link can be
pulled from the bolt.

Caution!

Crushing and shearing sections in the lifting
gear area.

Parking the implement

The implement can be parked in two positions (R and
H).

• Do not set the hydraulic

control valve to floating
position if the support
stand is raised.

Attention! (STOP)

The support stand should not be raised too high

- if the implement is parked in ”

” position and the

hydraulic control valve is set to floating position.

The drive shaft could thus be damaged as it is telescoped
on to the bar (0mm).

Beware!

Before

uncoupling

the lower link,

always secure

the bolt 13a with

the lever 13b.

48-00-24

064-01-014

STOP

0 mm

064-01-015

Содержание NOVACAT 225 H























































Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды

Poettinger NOVACAT 225 H, Руководство оператора

Результаты поиска

Содержание NOVACAT 225 H

Отзывы:

Похожие инструкции для NOVACAT 225 H

Бренды по названию

Популярные бренды