Poettinger NOVACAT 225 H Скачать руководство пользователя | Manualshive

Страница: 40 / 54

background image

- 40 -

1300_GB-ANHANGB_GELENKWELLE

PTO SHAFT

GB

Supplement - B

Instructions for working

The permissible pto speed may not be exceeded when
using the implement.
- The hitched implement may continue to run after the

pto is switched off. Work may only be performed once
it has reached complete standstill.

- The cardan shaft must be put down or secured using a

chain when the implment is parked. Do not use safety
chain (H) to suspend the cardan shaft.

Wide-angle joint:

  Maximum angle in operation and at standstill 70°.
Standard joint :
  Maximum angle at standstill 90°.
  Maximum angle in operation 35°.

Maintenance

Replace work covers immediately.

- Lubricate with a brand-name grease before starting

work and every 8 hours worked.

- Before any extended period of non-use, clean and

lubricate driveshaft.

For winter working, grease the tube guards, to avoid

them freezing together.

Matching driveshaft to tractor

To determine the actual length required, hold the two halves
of the driveshaft side by side.

T rimming procedure

- To adjust the length, place the pto halves in the shortest

operating position (L2) next to one another and mark.

Caution!

• Note the maximum operating length (L1)

- Aim at the maximum possible tube superimposition

(min. 1/2 X)

•  Trim the inner and outer protective tube equally
•  Attach overload fuse (2) at the implement!
•    Always check that drive shaft locks are securely engaged

before starting work.

Safety chain

-   Use chain to prevent tube guard from rotating.
  Ensure sufficient swivel space for the cardan shaft!
-  Trim the safety chain so that it cannot wind around the

cardan shaft.

8

Be advised!

Only use the

cardan shaft sup-

plied or stated;

otherwise the

warranty claims

for any damage

are not valid.

«
...
38
39
40
41
42
...
»

Содержание NOVACAT 225 H























































Отзывы:

Нет отзывов

Похожие инструкции для NOVACAT 225 H

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Eastern Jungle Gym Страницы: 17

Бренд: Vahle Страницы: 96

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: P.Lindberg Страницы: 76

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: SandenVendo Страницы: 19

Бренд: Vahterus Страницы: 31

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: Wassermann Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды