Platinum Access Systems BLSW1016 Скачать руководство пользователя | Manualshive

Страница: 9 / 34

background image

10

TECHNICAL SUPPORT: (909) 259-6001

BLSW1016

INSTALLATION

Non-Contact Sensors (Photoelectric Sensors) Installation:

One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists,

such as the perimeter reachable by a moving gate or barrier.

Install photoelectric sensors to protect

against any entrapment or safety conditions

encountered in your gate application.

We recommend the use of EMX IRB-325

photoeyes to comply with UL325.

Open Position

Photo Beam Device

Reflector

Potential Entrapment Area

Consult the UL325 device installation manual for more detail information about the usage,

installation and maintenance of this device.

Note: This type of installation DOES NOT reverse the gate all the way back to its limits when the photo-

beam is obstructed. This installation is only to protect against entrapment and to comply with UL325.

TX

EMX Model

IRB-325

Shown

Connection ‘1’ (C1)

Connection ‘2’ (NC1)

WARNING – To reduce the risk of severe injury or death to person, please to follow these instructions:

BLSW1016 Manual_Layout 1 5/8/2015 5:06 PM Page 10

«
...
7
8
9
10
11
...
»

Содержание BLSW1016



































Отзывы:

Нет отзывов

Похожие инструкции для BLSW1016

Бренд: WALKY Страницы: 12

Бренд: Ginnys Страницы: 5

Бренд: PAC Страницы: 6

Бренд: Genie Страницы: 2

Бренд: Winco Страницы: 8

Бренд: Tower Hobbies Страницы: 16

Бренд: tousek Страницы: 48

Бренд: SOMFY Страницы: 32

Бренд: SOMFY Страницы: 72

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 96

Бренд: CAME Страницы: 112

Бренд: CAME Страницы: 2

Бренд: USAutomatic Страницы: 60

Right Angle CN762

Бренд: Rival Страницы: 4

Бренд: Somati system Страницы: 34

Бренд: Chamberlain Страницы: 88

Бренд: Chamberlain Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды