Platinum Access Systems BLSW1016 Скачать руководство пользователя | Manualshive

Страница: 12 / 34

background image

TECHNICAL SUPPORT: (909) 259-6001

BLSW1016

13

Installation: Alarm Reset Switch & Warning Placards

Alarm Reset Switch Installation: (UL 325 standard requires)

An audible alarm to go off after two consecutive events detected by the primary entrapment protection

of the gate operator. The audible alarm will continue to sound for 5 minutes or until a stop command

gets actuated. The Stop command can be actuated in two different forms.

1. The Built in Stop switch on the Control Box.

2. The External Stop button within the sight of the gate, away from moving parts of the gate and out

of reach of children.

STO

P

COM

N.C.

STOP

6'

5'

Minimum

Manual Stop

Button

Warning Placard Installation:

All Warning Sings and Placards must be mounted where visible in the area of the gate.

A minimum

of two (2) Warning Placards shall be mounted. (One on each side of the gate).

WARNING – To reduce the risk of severe injury or death to person, please to follow these instructions:

BLSW1016 Manual_Layout 1 5/8/2015 5:06 PM Page 13

«
...
10
11
12
13
14
...
»

Содержание BLSW1016



































Отзывы:

Нет отзывов

Похожие инструкции для BLSW1016

Бренд: FAAC Страницы: 8

Бренд: CAME Страницы: 40

ThermoMark 5150

Бренд: Wayne-Dalton Страницы: 4

Бренд: Delton Страницы: 8

Бренд: CAME Страницы: 52

Бренд: tau Страницы: 40

Бренд: Elite Страницы: 22

Бренд: Elite Страницы: 38

Бренд: Gainwise Страницы: 17

Бренд: V2 Страницы: 29

Бренд: Beninca Страницы: 22

Бренд: tau Страницы: 36

Бренд: CAME Страницы: 72

Бренд: Beninca Страницы: 32

Бренд: Phoenix Doors Страницы: 13

Бренд: Calimet Страницы: 22

Бренд: vds Страницы: 13

Бренд: CAME Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды