Platinum Access Systems BLSW1016 Скачать руководство пользователя

Страница: 3 / 34

TECHNICAL SUPPORT: (909) 259-6001

BLSW1016

SAFETY INFORMATION

1. READ AND FOLLOW ALL INSTRUCTIONS MANUAL BEFORE ATTEMPTING ANY INSTALLA-

TION.

2. Should never let children play with gate controls. Keep the remote control away from children.

3. Always keep people and objects away from the gate. “NO ONE SHOULD CROSS THE PATH OF

THE MOVING GATE”.

4. Check and test the gate operator monthly. The gate MUST reverse on contact with a rigid object

or when an object activates the non-contract sensors. After adjusting the force or the limit of trav-

el, retest the gate operator. Failure to adjust and retest the gate operator properly can increase

the risk of injury or death.

5. 7KHJDWHV\VWHP0867EHPDLQWDLQHGSDYHDTXDOL¿HGVHUYLFHSHUVRQLQVSHFWUHSDLURU

adjust your system if any unusual behavior is observed or suspected.

6. Some companies offer a scheduled preventive maintenance service.

7. '2127(;&(('WKHHTXLSPHQWVSHFL¿FDWLRQV

8. Insure a safe and proper installation.

9. ,QVWDOOWKLVHTXLSPHQWLQDFFRUGDQFHZLWKWKH8/VSHFL¿FDWLRQV

10. All installation MUST have secondary protection devices against entrapment, such as edge sen-

sors and photo beams especially in places where the risk of entrapment is more likely to occur.

11. Gate is for vehicles only, a separate entrance for pedestrians is required.

12. SAVE THESE INSTRUCTIONS

SAFETY DEVICES:

1. Remove the Power Harness for the control board.

2. Check that all mounting hardware of the gate operator is properly tightened.

3. Ensure that the gate moves freely.

4. Check the battery for the following:

Battery connections must be free of corrosion.

Battery voltage must be 26.5 VDC minimum (fully charged battery).

5. Reconnect the Power Harness for the control board.

6. Make sure every installation has a minimum of one safety device (such as photo beams or loop

detector).

7. Check for Reverse Sensitivity.

8. Make sure that all areas around the gate are safe and secure.

WARNING – To reduce the risk of severe injury or death to person, please to follow these instructions:

BLSW1016 Manual_Layout 1 5/8/2015 5:06 PM Page 4

Содержание BLSW1016



































Результаты поиска

Содержание BLSW1016

Отзывы:

Похожие инструкции для BLSW1016

Бренды по названию

Популярные бренды

Platinum Access Systems BLSW1016, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание BLSW1016

Отзывы:

Похожие инструкции для BLSW1016

Бренды по названию

Популярные бренды