Philadelphia Scientific BOS-CB6700 Скачать руководство пользователя

Страница: 64 / 84

Philadelphia Scientific

iBOS

Pro 6 Series Installation Manual

Page 64 of 84

8.3 Sentinel

™

Check connection to the input

socket on the sentinel

Yes

LED’s not lighting

Is the Controller on?

Green LED is

flashing

CHARGER NO

START

– Amber LED

Flashing

Connected for more than 5

minutes (charger didn't start)

Verify all Charger

systems (Fuses, AC

Power, Circuit Boards)

and check battery

capacity.

Slow Flash

(1/sec)

Indicates the Sentinel is registered

with the controller but has not received

or has lost the assigned voltage

Charger shows in

queue but charger

is still charging

This may also appear

on the Scrolling

Display as a battery

to take

Check Charger

programmed settings,

some chargers are set to

force a cool down by

appearing to still be

charging a battery

Modify CHARGER

SETTINGS if

needed.

Battery was taken as

indicted by Display

but truck/pallet jack

gauge showed

“EMPTY”

Verify truck/pallet jack

calibration is correct

based on battery fleet

needs

Verify VPC on

battery, look for weak

cells or low acid

CALL TRUCK

SERVICE

COMPANY

Charger may be in a

Refresh charge

Push STOP on

charger and take

battery

SCORE CARD:

Charger “Not

Reporting In”

Check Sentinel

Sentinel has no

power (

no LED’s

are on)

Sentinel has power

(

LED’s are on)

Verify Charger is

operational, trouble

shoot charger

Check Upstream

Sentinel is lit.

For assistance,

Contact

Philadelphia Scientific

Customer Service

Check Cable to sentinel is CAT3

and passes the straight through

wire test.

Was there a Charger

No Start? Check

charger function.

Fast Flash

(>1/sec)

Slow Flash

(1/sec)

Fast Flash

(>1/sec)

Indicates the Sentinel is not

registered but is getting power.

Connected for more than 7

days with no charger activity

Connect a Battery if

still flashing check

quick tap

Verify Pins are

straight. If bent,

straighten and

reinstall at new

location

Sentinel is powered

by control box,

check power to the

bus on the control

box.

Sentinel still not

functioning

Yes

Ensure Pool Voltage is

set in the control box.

Settings/Pool &

Chargers

Check

connection to

the input socket

on the sentinel

Check Cable to

sentinel is CAT3

and passes the

straight through

wire test.

See Appendix A for further information on Sentinels

™

Содержание BOS-CB6700





















































































Результаты поиска

Содержание BOS-CB6700

Отзывы:

Похожие инструкции для BOS-CB6700

Бренды по названию

Популярные бренды

Philadelphia Scientific BOS-CB6700, Руководство по установке

Результаты поиска

Содержание BOS-CB6700

Отзывы:

Похожие инструкции для BOS-CB6700

Бренды по названию

Популярные бренды