Pfaff 3307-1 SERIES Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 132

background image

121

Adjustment

13

.51

Internet update of the machine software

The machine software can be updated with PFAFF ﬂash programming. For this purpose
the PFP boot program (from

version

3.25

on) and the appropriate control software for the

machine type must be installed on a PC. The transfer of the data to the machine can be
carried out with a null modem cable (part no.

91-291 998-91)

or with an SD-card. The

SD-card must be formatted in the

FAT16

format and must not exceed a capacity of

2

GBytes

.

The PFP boot program and the control software of the machine type can
be downloaded from the PFAFF-homepage using the following path:

www.pfaff-industrial.com/pfaff/de/service/downloads

13

.51.01

Update with null modem cable

After downloading the PFP tool and the control software, open the PFP program.

Select the

machine type

and under control unit

P320.

The software version is displayed under

report

.

●

●

●

Switch off the machine.
Connect the PC (serial interface or appropriate USB-adapter) and the machine control unit
(

RS232

). To do so disconnect the plug of the control panel.

While the machine software is being updated, no setting up, maintenance or
adjustment work may be carried out on the machine!

Switch on the machine, keeping the boot key

1

pressed.

Press the "OK" button.
The software update is carried out, the update progress is shown on the bar display of
the PFP boot program.
During the updating process the machine must not be switched off.
When the update has been completed, switch off the machine and end the PFP boot
program.
End the connection between the PC and the machine control unit and reconnect the
control panel to the machine control unit.

●

●

●

●

●

●

●

3307

P

320

Choice:
Machinetyp: 3307
Control unit: P320
Softwarenumber:
79-0011-0366/001

«
...
119
120
121
122
123
...
»

Содержание 3307-1 SERIES





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3307-1 SERIES

Бренд: UNIS Страницы: 19

Бренд: Singer Страницы: 66

Бренд: DURKOPP ADLER Страницы: 46

Jem Platinum 720

Бренд: Janome Страницы: 41

Бренд: Singer Страницы: 33

Бренд: Singer Страницы: 47

Бренд: Pfaff Страницы: 50

Sweepmaster B1200 RH

Бренд: HAKO Страницы: 64

Бренд: Datasensor Страницы: 161

3100 SERIES 569U

Бренд: Singer Страницы: 22

KM 70/30 C Bp Adv

Бренд: Kärcher Страницы: 147

Бренд: Kärcher Страницы: 22

Бренд: Spektrum Страницы: 44

Бренд: JUKI Страницы: 32

NOVAMATIC NM 2830

Бренд: FUST Страницы: 49

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды