Peri SKYDECK Скачать руководство пользователя страница 63

Страница: 63 / 102

41.1

2.8

41.1

41.2

41.3

41.2

90°

lic

A11 Inclined slabs

Bracing with Tension Unit SD

Bracing angle

selection: see Table

A15.02.
Tension forces and prop loads: see
Tables A15.03 – A15.08.

Assembly

1. Position slab prop with tripod.
2. Place the Tension Unit Upper Part

(41.1) on the end plates of the Main
Beam SLT (2.8) and attach the Main
Beam to the Drophead SFK.
(Fig. A11.03)

3. Swivel up the Main Beam with the

second slab prop. Tension Unit must
lie on the end plates of the Main
Beam SLT.

4. Mount Base Plate (24) on a suffi-

ciently load-bearing surface area, e.g.
using PERI Anchor Bolt 14/20x130,
Item no. 124777. Take into considera-
tion the Technical Data Sheet!

5. Insert the Tie Yoke of the Tension

Unit Upper Part onto the Tie Rod
(41.3), secure with the Hex. Nut
SW 30/50 (42), and attach to the
Tension Unit Upper Part.
(Fig. A11.03 + A11.04)

6. Fix Tension Unit Lower Part (41.2) to

the Base Plate by means of bolts, and
secure bolts using cotter pins.
(Fig. A11.02)

7. Insert Tie Yoke of the Tension Unit

Lower Part onto the Tie Rod, secure
with Triple Wingnut DW 15 (43), and
attach to the Tension Unit Lower Part.
(Fig. A11.05 + A11.06)

8. Tension the Tension Unit using a Triple

Wingnut.

Components

Base Plate RS

24.1

Anchor Bolt PERI 14/20 x 130

Tension Unit SD

Fig. A11.03

Fig. A11.06

Fig. A11.04

Fig. A11.05

Fig. A11.02

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

SKYDEKC AuV_ex_791458.indb 61

13.12.16 16:57

Содержание SKYDECK







































































































Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды

Peri SKYDECK, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды