Peri SKYDECK Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 102

Peri SKYDECK Скачать руководство пользователя страница 36

34

9/12

x

y

13

x

y

9*

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

A6 Shuttering around columns

1 recessed panel

Maximum column dimensions
x = 55 cm, y = 138 cm.

Secure filler plates with nails!

Install Edge Beam SRT-2 150 vertically
(9) or Filler Timber SPH 150 (12).
During use, permissible loads must be
observed; see Tables: Fillers / Forming
around columns

Take into account the supporting
direction of the formlining.

Alternatively:
Install Edge Beam SRT-2 150 (9*) in a
suspended position. (Fig. A6.03)
Flatly position Filler Timber SPH or in-
stall timber (13) supplied by the contrac-
tor.

For 27 mm formlining: height of
timber = 47 mm.
Permissible widths of influence for
flat Filler Timber SPH, see Table A6.02.

Components

9

Edge Beam SRT-2 150

10

Edge Beam SRT-2 75

9*

Edge Beam SRT 150, suspended

10*

Edge Beam SRT 75, suspended

12

Filler Timber SPH

13

Timber

Fig. A6.02

Fig. A6.04

Fig. A6.03

Fig. A6.01

Width of Influence

SKYDEKC AuV_ex_791458.indb 34

13.12.16 16:56

«
...
34
35
36
37
38
...
»

Содержание SKYDECK







































































































Отзывы:

Нет отзывов