Peri SKYDECK Скачать руководство пользователя страница 55

Страница: 55 / 102

2.7

45.1

A9 SKYDECK platforms

Platform installation

Risk of falling!

– Cantilevers should not have form-

work erected or be stepped on be-
fore being firmly secured with ten-
sion chains.

– When lingering on the slab form-

work, measures must be taken to
prevent falling, e.g. PPE.

– Clearly mark unsecured building

edges!

Begin with the platform assembly in
one area in which there is no risk of
falling to the rear or at the side (e.g.
Area II, see Ground Plan Fig. A9.01).

1. With the help of the Erection Aid

SSH, access the recess of the plat-
form decking and pull the platform
out from its safe position. (Fig. A9.12)

2. Move the platform into position at an

angle from above in front of the last
panel onto the cantilevered main beam.

3. By further lowering the platform, pos-

itive assembly is carried out:

– The slide (45.1) on the underside of

the platform is secured when posi-
tioned in the platform support (2.7) on
the Main Beam SLT 375. (Fig. A9.12a)

The platform is locked in position
and secured against tipping.

– The slide safety device locks into

the teeth of the main beam.

The platform is secured against
moving in the longitudinal
direction of the beam.

4. Detach both crane hooks. Site per-

sonnel must wear personal protection
equipment (PPE) to prevent falling!

– Crane eye swivels downwards and

the securing hook grips under the
self-draining edges of the main
beam. If necessary, press down
the crane eye.

The platform is additionally
secured against tipping and
lifting. (Fig. A9.12b)

5. Install other platforms in the same

way with the shuttering aid.

6. Close infill areas < 75 cm using con-

tractor’s own resources, e.g. scaffold
planks 24 x 4.5 cm.

Fig. A9.13

Fig. A9.12a

Fig. A9.12b

Securing hook

Shuttering Aid
SSH

Self-draining
edges

Anti-slip device

7. Handrails for infill areas are created

using handrail boards 3 x 15 cm and
toe boards (use nail holes in platform
guardrails) or standard couplings and
scaffold tubes.

For difficult assembly situations, e.g.
wind, guide the platform with 2 shutter-
ing aids. (Fig. A9.13)

Fig. A9.12

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

SKYDEKC AuV_ex_791458.indb 53

13.12.16 16:57

Содержание SKYDECK







































































































Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды

Peri SKYDECK, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды