manualshive.com logo in svg

Peri SKYDECK, Инструкция по сборке и эксплуатации

Поделиться
Скачать
Peri SKYDECK Скачать руководство пользователя страница 27

25

2.8

7

11

9 12

2/2.5

7.1

2.1

7.1

7

3

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

A5 Compensations

Combihead SCK

Use of longitudinal and transverse infills 
up to 25 cm. 
The cantilever of the Head Plate is in 
longitudinal direction ≤ 19 cm, in trans-
verse direction ≤ 12.5 cm. 
The Combihead (7) (Fig. A5.11) is a se-
cure, non-movable and non-twisting 
support for:

 

– Main Beam SLT 225 (2). 

 

– SLT 150 (2.5). (Fig. A5.10)

 

– Panel SDP (3). (Fig. A5.12)

 

– Edge Beam SRT (9) and Filler Timber 

SPH (12) or timber provided by the 
contractor with b = 3.8 – 8 cm and  
h = 9.8 cm. (Fig. A5.13)

 

– End Support SSL (11). (Fig. A5.14)

Mounting the main beam

The Main Beam SLT must be mounted 
in the middle of the beam support of 
the SKYDECK Heads. The main beam 
connection (2.1) encloses the main 
beam support (7.1) of the head.  
(Fig. A5.10)

The Combihead SCK has 2 main beam 
supports and can be installed in both  
directions. In infill areas, the cantilever 
points towards the compensation.

Exceptions:

The cantilever points towards the main 
beam

 

– when using the End Support,  

(Fig. A5.14)

 

– when infill ≤ cantilever. (Fig. A5.14a)

Placing the main beam

With inset props, the cantilever of the 
Combihead always points towards the 
main beam.
Position the Combihead so that the 
main beam support is securely posi-
tioned in the groove (2.8) of the main 
beam.  
(Fig. A5.15)

Fig. A5.10

Fig. A5.11

Fig. A5.13

Fig. A5.15

Fig. A5.12

Fig. A5.14

Fig. A5.14a

SKYDEKC AuV_ex_791458.indb   25

13.12.16   16:55

Содержание SKYDECK







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды