Peri SKYDECK Скачать руководство пользователя страница 54

Страница: 54 / 102

2.6

III

A9 SKYDECK platforms

Open edge areas (Area lll)

Start shuttering on structural constraint
points (e.g. wall, casting segment) and
work towards the corner table, Area II.

Slab area (Area lV)

When all edge areas are formed, the
slab surface Area IV is formed in the
usual way with SKYDECK.

Regarding the tightness of the panel
joints, e.g. for casting segments/setting
of stopends, push the panels tightly
together and secure on the last main
beam with Panel Wedge Clips SPKK (20).

Components

Main Beam SLT 225

2.6

Main Beam SLT 375

Edge Beam SRT

Timber

Panel Wedge Clip SPKK

SKYDECK Platform SDB 300

SKYDECK Platform SDB 150

SKYDECK Platform SDB 225

Fig. A9.10

Infill areas

Risk of falling!

– Do not erect formwork or step

on cantilevered tables before the
tension chains are securely fixed.

– When lingering on the slab form-

work, measures must be taken to
prevent falling, e.g. PPE.

– Clearly mark unsecured building

edges!

Close infill areas in the inner area, close
infill areas at unsecured building edges
after the platforms have been installed.

Fig. A9.11

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

SKYDEKC AuV_ex_791458.indb 52

13.12.16 16:57

Содержание SKYDECK







































































































Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды

Peri SKYDECK, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды