manualshive.com logo in svg

Peri SKYDECK, Инструкция по сборке и эксплуатации

Поделиться
Скачать
Peri SKYDECK Скачать руководство пользователя страница 46

44

17

17.1

17

17

18

SKYDECK Panel Slab Formwork

 Instructions for Assembly and Use – Standard Configuration

A8 Cantilevers, Guardrails

SKYDECK Guardrail Holder 

SGH and Guardrail Post 

SGP

 

Risk of falling!
During assembly, measures must be 
taken to prevent falling, e.g. PPE!

Assembly

Continuous mounting of Guardrail Hold-
er SGH (17) between the panels. To do 
so, place the guardrail holder laterally 
offset on the main beam and slide in. 
Spacing max. 1.55 m. 

 

Wind safeguard measure: with wind 
speeds > 90 km/h, remove the top 
guardrail board. Adapt working area ac-
cordingly to suit changed guardrail situa-
tion. 

After the last row of panels, mount the 
Guardrail Holder SGH for the End Guard-
rail Frame on all main beams:
1. Start with the guardrail holder on the 

outer right-hand side (17.1) – as 
viewed when standing in front of the 
formwork. Mounting bar is pointing to 
the left. 

2. Mount all other guardrail holders (17) 

with the mounting bar pointing to the 
right. (Fig. A8.09) The mounting bars 
overlap in the first bay.

3. Insert guardrail posts (18). 
4. Insert guardrail boards and secure 

with nails. (Fig. A8.10)

Components

17

  Guardrail Holder SGH

18

  Guardrail Post SPG

20

  Panel Wedge Clip SPKK

Fig. A8.10

Fig. A8.09

SKYDEKC AuV_ex_791458.indb   44

13.12.16   16:56

Содержание SKYDECK







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды