Peri SKYDECK Скачать руководство пользователя страница 30

Страница: 30 / 102

1 11

2.5

2,25 m (+5 cm)

≤ 75 cm

1,5 m

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

A5 Compensations

Fig. A5.20

Triangular Frame SDR

150/75, 75/75

Form infill areas with inclined walls us-
ing triangular frames.

Forming the infills

1. Continue forming in the system as

long as possible.

2. Carry on forming operations with filler

panels as well as transversely
inserted panels – as for longitudinal
and transverse compensations.

3. Lay Triangular Frame (14) on the sup-

port (Main Beam, Prophead or Combi-
head, End Support). (Fig. A5.20)

4. Place the support on the wall side.
5. Install formlining and secure in posi-

tion with nails.

Longitudinal compensations

Secure filler plates with nails!

Drophead infills up to 2.25 m + 5 cm.
Prophead infills up to 2.25 m.

Length of room minus n x 2.30 m
(2.25 m) = compensation area.
See Tables: Fillers / Forming around
columns.

Forming longitudinal compensations
between 75 cm and 2.25 m

1. Continue forming with prop, Compen-

sation Beam SLT 150 (2.5) and Panel
SDP (3) as in the standard bay.
(Fig. A5.21)

2. Depending on the required load-bear-

ing capacity, continue forming with
filler panels. See PERI Tables.

3. Forming of gaps up to 75 cm, see

following pages.

– Take into account the load-bearing

capacity and supporting direction of
the formlining. See PERI Tables.

– Timbers are securely nailed on the

panel inner side before panels are
assembled. Use the nail holes in the
panel edge struts.

Fig. A5.21

SKYDEKC AuV_ex_791458.indb 28

13.12.16 16:55

Содержание SKYDECK







































































































Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды

Peri SKYDECK, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды