Peri SKYDECK Скачать руководство пользователя страница 26

Страница: 26 / 102

9.1/10.1

9/10

9*/10*

SKYDECK Panel Slab Formwork

Instructions for Assembly and Use – Standard Configuration

A5 Compensations

System components

For the realization of compensations
and shuttering of columns, a range of
system components is available.

Secure filler plates with nails!

Edge Beam SRT 150-2,

SRT 75

Install vertically (Fig. A5.01) or
suspended. (Fig. A5.02)
The locking pin (9.1/10.1) secures
the Edge Beam SRT 150 (9) or
SRT 75 (10):

– to the Main Beam SLT in a longitudi-

nal direction. (Fig. A5.01 + A5.02)

– to the Prophead SSK in a transverse

direction. (Fig. A5.03)

– to the Combihead SCK (7) in a longi-

tudinal direction. (Fig. A5.04)

– in the End Support SSL (11) in a longi-

tudinal direction. (Fig. A5.07)

Filler Timber SPH

Install Filler Timber SPH (12) vertically or
horizontally.

– to the Combihead SCK. (Fig. A5.04)

– nailed laterally on the panel.

– horizontally, transverse to the sus-

pended Edge Beam SRT. (Fig. A5.05
+ A5.06)

End Support SSL

Use the End Support SSL as height ad-
justment for the transition from a stand-
ard bay to an infill area.
(Fig. A5.07)
The End Support SSL must always be
directly supported by means of a Prop-
head, Drophead or Combihead.
(Fig. A5.08)

Components

Main Beam SLT

Panel SDP

Combihead SCK

Edge Beam SRT-2 150

Edge Beam SRT-2 150, suspended

Edge Beam SRT-2 75

10*

Edge Beam SRT-2 75, suspended

End Support SSL

Filler Timber SPH

SRT vertical

Fig. A5.01

Fig. A5.02

Fig. A5.03

Fig. A5.04

Fig. A5.07

Fig. A5.05

Fig. A5.06

Fig. A5.09

Fig. A5.08

No End Support SSL without any direct
support through Prophead, Drophead or
Combihead.

SRT suspended*

The asterisk (*) refers to the installation
in a suspended position.

End Support SSL

SKYDEKC AuV_ex_791458.indb 24

13.12.16 16:55

Содержание SKYDECK







































































































Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды

Peri SKYDECK, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание SKYDECK

Отзывы:

Бренды по названию

Популярные бренды