Pella Insynctive Скачать руководство пользователя страница 14

Страница: 14 / 21

PELLA

INSYNCTIVE

INTEGRATED ENTRY DOOR SENSOR PRODUCT GUIDE

To replace the battery on LOCK SENSOR for Entry Door by Pella
with Deadbolt Lock:

• Use a flathead screwdriver to carefully remove the battery cover

from LOCK SENSOR.

•  Carefully remove the battery and replace with a CR2 battery.
•  Install the battery cover back onto SENSOR.
•  Wait 2 minutes, then test SENSOR by locking then unlocking the

entry door with installed SENSOR. BRIDGE should beep twice when
unlocked. Resyncing SENSOR is not required after battery change.

To replace the battery on LOCK SENSOR for Entry Door by Pella
with Multipoint Lock:

• Remove the lock transmitter from your entry door, then lift up

the corner of the plastic cover to reveal the battery.

• Carefully replace with a CR2032 battery, ensuring that the plus

(+) side of the battery faces toward you.

• Replace clear plastic cover over battery and ensure that battery

is seated, then insert lock transmitter back into your entry door.

• Close and lock the door within 2 minutes of replacing the

battery to teach SENSOR what type of product it is installed in.

• Wait 2 minutes, then test SENSOR by unlocking your entry door

with installed SENSOR. BRIDGE should beep twice. Resyncing
SENSOR is not required after battery change.

WARNING: Batteries carry the risk of fire, explosion and

burns. Do not recharge, disassemble or incinerate.

IMPORTANT NOTES:

• Electrostatic-sensitive. Avoid touching the antenna or circuit

board when changing the battery.

• Failure to change battery promptly when low will impair

SENSOR performance.

• Properly dispose of used batteries based on your local

requirements. A best practice is to dispose of batteries at
your local home chemical collection center.

California Only:

Contains perchlorate material. See dtsc.ca.gov/hazardouswaste/
perchlorate for any special handling regulations.

ADDITIONAL INSTRUCTIONS

(continued)

LOCK

SENSOR

BATTERY

COVER

BATTERY

COVER

PLASTIC COVER

OPEN/CLOSE

SENSOR

ENTRY DOOR BY PELLA

WITH DEADBOLT LOCK

ENTRY DOOR FROM PELLA

WITH MULTIPOINT LOCK

Содержание Insynctive






















Результаты поиска

Содержание Insynctive

Отзывы:

Бренды по названию

Популярные бренды

Pella Insynctive, Руководство по эксплуатации продукта

Результаты поиска

Содержание Insynctive

Отзывы:

Бренды по названию

Популярные бренды