manualshive.com logo in svg

Pella Insynctive, Руководство по эксплуатации продукта

Поделиться
Скачать
Pella Insynctive Скачать руководство пользователя страница 13

PELLA

®

 INSYNCTIVE

®

 INTEGRATED ENTRY DOOR SENSOR PRODUCT GUIDE

  | 

 13

HOW TO FIND PRODUCT MANUFACTURER’S CODE

Each Pella

®

 Insynctive

®

 product contains a label with a 

Manufacturer’s Code that will be required to help Pella Customer 
Service identify the product if service is required. To locate 
the Manufacturer’s Code for LOCK SENSOR for Entry Door by 
Pella with Deadbolt Lock, remove LOCK SENSOR from the jamb 
and look at the sticker on the back of the device. To locate the 
Manufacturer’s Code for LOCK SENSOR for Entry Door by Pella 
with Multipoint Lock, pull lock transmitter from your entry door. 
The label is on the circuit board next to the battery. To locate 
the Manufacturer’s Code for OPEN/CLOSE SENSOR, remove the 
battery cover and carefully pull out the circuit board. The sticker 
will be located on the circuit board.

NOTE:

 Electrostatic-sensitive. Avoid touching the antenna or 

circuit board when accessing the Manufacturer’s Code.

CARE AND MAINTENANCE

•  Test Insynctive products at least once per year to help ensure 

proper operation.

•  Do not paint over SENSORS.

REPLACING BATTERIES

See 

Insynctive.Pella.com/Support

 for how-to videos.

When INTEGRATED ENTRY DOOR SENSOR battery is low, a signal 
will be sent to BRIDGE. To aid in identifying which SENSOR has a 
low battery, BRIDGE will beep twice and then issue a long tone 
when INTEGRATED ENTRY DOOR SENSOR with the low battery 
changes from locked to unlocked or opened to closed.

To replace the battery on OPEN/CLOSE SENSOR:

•  Use a flathead screwdriver to carefully remove the plastic 

endcap from the OPEN/CLOSE SENSOR. 

•  Grip the edges of the circuit board and pull it out to gain access 

to the battery.

•  Carefully slide out the battery and replace with a CR2 battery.
•   Slide circuit board back inside SENSOR and install the plastic 

endcap back onto the SENSOR. 

•  Wait 2 minutes, then test SENSOR by opening the entry door 

with installed SENSOR. BRIDGE should beep twice. Resyncing 
SENSOR is not required after battery change. 

ADDITIONAL INSTRUCTIONS

MANUFACTURER’S

CODE

CIRCUIT  

BOARD

BATTERY

OPEN/  

CLOSE  

SENSOR

CIRCUIT  

BOARD

PRODUCT CODE

OPEN/CLOSE SENSOR

BATTERY

CIRCUIT BOARD  

ANTENNA TRACED  

ON CIRCUIT BOARD  

(HIGHLIGHTED IN RED)

LOCK SENSOR FOR ENTRY DOOR BY PELLA 

WITH DEADBOLT LOCK

PRODUCT CODE

LOCK SENSOR FOR ENTRY DOOR BY PELLA  

WITH MULTIPOINT LOCK

Содержание Insynctive






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды