Pavone Sistemi JBX8 LCD Скачать руководство пользователя страница 11

Страница: 11 / 53

MENU

NAME

DESCRIPTION

INFO

Information:

Parameter menus that can be displayed for identification of the

device and its configuration.

TEST

Test

Menu of the instrument's hardware test operation procedures.

SETUP

Setup

Menu of the programmable parameters that determine the start-

up of the instrument.

Menu Message

Name

Description

Type

INFO FIRMWARE

Firmware code

Indication of the installed Firmware code

Screen

FULL SCALE

Full scale of the device

Indication of the set full scale value

Screen

N.OF CELLS

Number of cells enabled Indication of the number of enabled cells

Screen

FIELDBUS

Fieldbus present

Indication of the type of fieldbus configured

Screen

ADDRESS

Fieldbus address

Indication of the set fieldbus address. This menu

item is only displayed in the RS485 and PROFIBUS

configurations.

Screen

IP ADDRESS

Fieldbus IP address

Indication of the set fieldbus IP address. Item di-

splayed only in the PROFINET and ETHERNET/

IP configurations.

Screen

SUBNET

Fieldbus Subnet Mask

Indication of the set fieldbus subnet mask. Item

displayed only in the PROFINET and ETHERNET/

IP configurations.

Screen

ANALOG

OUT

Analog output configu-

ration

Indication of presence and type of analogue

output (Not present - Unipolar - Bipolar)

Screen

MEMORY

Optional Memory Con-

figuration

Indication of presence and type of memory

(None - Alibi memory)

Screen

In the case of PROFINET field bus: the IP address and Subnet Mask parameters are programmable by PLC and are

updated in this menu only when the device is switched on; after a change in these parameters from the PLC, it is

necessary to switch the device off and on again to display the correct value. It is important to remember that even

if you set the IP address and subnet mask parameters in Temporary mode, these parameters are not automatically

updated in the device. Moreover, when the device is turned off and on again, these parameters will be all set to

0.0.0.0.

Содержание JBX8 LCD






















































Результаты поиска

Содержание JBX8 LCD

Отзывы:

Бренды по названию

Популярные бренды

Pavone Sistemi JBX8 LCD, Техническое руководство

Результаты поиска

Содержание JBX8 LCD

Отзывы:

Бренды по названию

Популярные бренды