Partner Tech International PT-5700 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 88

Partner Tech International PT-5700 Скачать руководство пользователя страница 35

Power Management Setup Option

27

LPT & COM

When this item is enabled, the system will restart the power-saving timeout counters when any activity is detected on
the serial ports, or the parallel port. The default setting is LPT/COM.

HDD & FDD

When this item is enabled, the system will restart the power-saving timeout counters when any activity is detected on
the hard disk drive or the floppy diskette drive. The default setting is ON.

PCI Master

When set to Off, any PCI device set as the Master will not power on the system. The default setting is OFF.

PowerOn by PCI Card

Use this item to enable PCI activity to wakeup the system from a power saving mode. The default setting is Disabled.

Modem Alarm Resume

Enables any Ring-In signals from the modem to restore the system from a suspended state to an active state.

Disabled: Disable this function. (Default value)

Enabled: Enable modem ring resume.

RTC Alarm Resume

When set to Enabled, the following two fields become available and you can set the date (day of the month), hour,
minute and second to turn on your system. When set to 0 (zero) for the day of the month, the alarm will power on your
system every day at the specified time. The default setting is Disabled.

Date (of Month)

When set to “0” the system powers on everyday at the time specified in the “Time (hh:mm:ss) Alarm” field. Select a
date from 1 to 31 for the system to power on at the time specified in the “Time (hh:mm:ss) Alarm” field. The default
setting is 0.

Resume Time (hh:mm:ss)

Set the time for the system to power on as defined in the ‘Date (of Month) Alarm” field. The time set in this field must
be later than the time in the RTC time.

IRQs Activity Monitoring

Select the item and press <Enter> to open the following menu:

«
...
33
34
35
36
37
...
»

Содержание PT-5700

























































































Отзывы:

Нет отзывов