Paradyne FrameSaver NP 100 Скачать руководство пользователя страница 83

Страница: 83 / 159

5 Diagnostics

5-4

NetPath 100 User’s Manual - Installation Guide

980-001-0210K

November

2000

Device
Status / Test

The Device Status / Test screen provides base module status and access to system tests.

The Device Status / Test screen is shown in Figure 5-2.

Figure 5-3 Device Status / Test Screen

CSU Fault, Netw Set Loop, Frame Mgr Fault - Display (blank) or the highest prior-

ity Fault or Network Loop causing a disruption of the data path.

Refer to the Appendix in this manual for a list and description of fault and loop
displays.

Test Mode - Allows selection of the following mutually exclusive test modes:

Clear - Terminates operator or Telco-initiated Loopbacks, BERT,
and Test Packet tests.

Line Lp to Netw - Sets a Line Loopback at the T1 interface toward the Network.

Payld Lp to Netw - Sets a Payload Loopback in the CSU toward the Network.

Send LoopUp - Sends a T1 Line Loopback code toward the Network.

Send LoopDn - Sends a T1 Remove Line Loopback code toward the Network.

***************************** Device Status / Test *****************************

Name: F@43802

CSU Fault: T1 ID: NONAME

Netw Set Loop:

Test Mode [T=]

1) Clear Frame Mgr Fault: LMI Netw Failure

2) Line Lp to Netw

3) Payld Lp to Netw High Speed Interface

4) Send LoopUp DTR: On

5) Send LoopDn RTS: On

>>6) QRSS to Netw<< Power: On

7) Alt Ones to Netw Interface: ITU-V35

8) 2047 Payld to Netw

9) 2047 Payld to User

10) Loop to User

11) Test Pkts to Netw

BERT: Blocks Sent: , , Block Errors: , , BlkErr Rate: 0.00E+00

Test Duration: 00:00:00

ResetTest[RT] InjectErr[IE secs] RebootExt[RE secs]

Help[?] Close[X] AutoUpdate[AU]

Содержание FrameSaver NP 100
































































































































































Результаты поиска

Содержание FrameSaver NP 100

Отзывы:

Paradyne FrameSaver NP 100, Руководство пользователя и инструкция по установке, Страница: 83 / 159

Результаты поиска

Содержание FrameSaver NP 100

Отзывы: