Paradyne FrameSaver NP 100 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 159

Paradyne FrameSaver NP 100 Скачать руководство пользователя страница 67

4 Operation

4-18

NetPath 100 User’s Manual - Installation Guide

980-001-0210K

November

2000

Frame Manager
Configuration

The Frame Manager Configuration screen allows you to view and alter parameters for
Frame Manager operations.

The Frame Manager Configuration screen is shown in Figure 4-9.

Figure 4-9 Frame Manager Configuration Screen

Configure Frame Manager

1. WAN Mgmt DLCI - Displays current DLCI value of the private network PVC or

Tunneled PVC for WAN management of the NetPath 100, as stored in the unit’s
non-volatile memory (NVM). This value may be entered using the unit’s rear
panel DLCI DIP Switches, or entered from this screen. Enter the DLCI number
only, for private network PVC. Preface the DLCI number with “T” for tunneled
PVC. Preface the DLCI number with “D” to have the WAN Mgmt IP Address
relearned each time the PVC returns to an “active” condition.

2. P/C Mgmt DLCI - Sets or disables the direction and PVC for Payload/CPE

management access to the NetPath 100. The first letter (P or C) determines which
direction, and the remainder indicates the DLCI value.

NOTE: The P/C Mgmt DLCI value must NOT be the same as WAN Mgmt DLCI.

CAUTION

If either WAN or P/C Mgmt DLCI value is changed, the
NetPath 100 will perform a system reset after the Save
[SA] command is issued. The system reset will terminate
any console session in progress and interrupt data
traffic.

3. LMI Protocol - Displays and allows the selection of the LMI protocol used. If set

to “None,” LMI traffic (if any) to or from the Network will be passed through the
NetPath unaffected, and the unit’s LMI alarms and status will be cleared.

************************** Frame Manager Configuration *************************

Name: F@43802

LMI Protocol [P=]

WAN Mgmt DLCI [D=#,T#orD#]: Disabled 1) None 3) "LMI"

P/C Mgmt DLCI [E=P#orC#]: Disabled >>2) ANSI"D" << 4) ITU"A"

X to Disable or 16 thru 991

------------- Network ------------ -------------- User --------------

T391/Status Enq Rate [S1=#]: 10 T392/Status Enq Timeout [S2=#]: 15

5 thru 30 seconds 5 thru 30 seconds

N392/Event Err Thres [T1=#]: 3 N392/Event Error Thres [T2=#]: 3

N393/Event Count [C1=#]: 4 N393/Event Count [C2=#]: 4

1 thru 10 1 thru 10

N391/Full Status Freq [F1=#]: 6 Force Full Status Response [F2=]

1 thru 255 >>1) Disable<<

2) Enable

PVC BECN/FECN Thres [B=#]: Disabled

X to Disable or 1 thru 895 seconds

Link Err Thres [L1=#]: Disabled Link Err Thres [L2=#]: Disabled

X to Disable or 1 thru 895 seconds X to Disable or 1 thru 895 seconds

Help[?] Save[SA] Cancel[X]

>

«
...
65
66
67
68
69
...
»

Содержание FrameSaver NP 100
































































































































































Отзывы:

Нет отзывов