Panasonic PT-SRZ34KC, Руководство по эксплуатации, Страница: 223 / 322

Chapter 4 Settings
—
[NETWORK] menu
ENGLISH - 223
2) Press the <
执行
> button.
f
The
[Art-Net]
screen is displayed.
3) Press
as
to select [Art-Net SETUP].
4) Press
qw
to switch the item.
f
The ite m s w ill s w itch each ti m e you press the button.
[OFF] Disables the Art-Net function.
[ON(2.X.X.X)] Enables the Art-Net function and sets the IP address to 2 . X . X . X .
[ON(10.X.X.X)] Enables the Art-Net function and sets the IP address to 10 . X . X . X .
[ON(MANUAL)]
Enables the Art-Net function and uses the IP address set in [WIRED LAN].
f
Proceed to Step
5)
w hen anything other than [OFF] is selected.
5) Press the <
执行
> button.
f
The
[Art-Net SETUP]
screen is displayed.
6) Press
as
to select an item, and press
qw
to switch the setting.
[NET] Enter [NET] to be used w hen the projector processes Art-Net.
[SUB NET] Enter [SUB NET] to be used w hen the projector processes Art-Net.
[UNIVERSE] Enter [UNIVERSE] to be used w hen the projector processes Art-Net.
[START ADDRESS]
Enter [START ADDRESS] to be used w hen the projector processes Art-Net.
7) Press
as
to select [STORE], and press the <
执行
> button.
f
The con fi r m ation screen is displayed.
8) Press
qw
to select [OK], and press the <
执行
> button.
Note
f
If [ON (2 . X . X . X) ] or [ON (10 . X . X . X) ] is selected, IP address is calculated and set auto m atically.
[Art-Net CHANNEL SETTING]
Set the assign m ent of the channel. Make settings to use the Art-Net function.
For the channel de fi nitions used for controlling the projector w ith the Art-Net function, refer to “Using Art-Net
function ” (
x
page 2 88 ) .
1) Press
as
to select [Art-Net].
2) Press the <
执行
> button.
f
The [Art-Net] screen is displayed.
3) Press
as
to select [Art-Net CHANNEL SETTING].
4) Press
qw
to switch the item.
f
The ite m s w ill s w itch each ti m e you press the button.
[2] Uses the channel assign m ent in standard setting.
[3]
*1
Uses the channel assign m ent w ith the setting that can nu m erically control the lens position.
[USER] C hanges the channel assign m ent.
[1]
Uses the channel assign m ent w ith SD Z21 K C series co m patible.
SD Z21 K C series: SD Z21 K C , SDS 20 K C , SDW 1 7K C , SD Z1 8K C
* 1 This ite m can be selected in the follo w ing case.
When the standard D C m otor unit installed in the Z oo m Lens ( Model No.: ET-D75LE6, ET-D75LE8, ET-D75LE 10C , ET-D75LE 20C ,
ET-D75LE 30C , ET-D75LE 40C) is replaced w ith the stepping m otor unit using the Stepping Motor Kit ( Model No.: ET-D75MKS 10) , or w hen a
projection lens w ith the stepping m otor is attached.
f
Proceed to Step 6) w hen anything other than [USER] is selected. The function assigned to the channel is
displayed by pressing the <
执行
> button.
f
Proceed to Step 5) w hen [USER] is selected.
5) Press the <
执行
> button.
f
The [Art-Net CHANNEL SETTING] screen is displayed.