Chapter 1
Preparation — About your projector
34 - ENGLISH
Note
f
This projector does not support audio output because it is not equipped with audio function. However, when SDI signal with audio is input to
the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-SDI 4 IN> terminal, a signal with audio is output from the <3G-SDI 1 OUT>/<3G-SDI
2 OUT>/<3G-SDI 3 OUT>/<3G-SDI 4 OUT> terminal.
f
To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the firmware version of the 3G-SDI Terminal
Board with Audio to be 2.00 or later. Confirm the firmware version of the 3G-SDI Terminal Board with Audio when it does not operate after
installing to the projector.
Consult your dealer regarding the version update to the latest firmware if the version is earlier than 2.00.
For details on how to confirm the firmware version, refer to “How to confirm the firmware version of the Interface Board (optional)”
(
x
page 35).
r
Interface Board for 12G-SDI (Model No.: ET-MDN12G10)
This board supports the SD-SDI signal, HD-SDI signal, 3G-SDI signal, 6G-SDI signal, and 12G-SDI signal.
2
5
5
4
1
3
1 <SDI 1 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
2 <SDI 2 IN/1 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 1
IN> terminal of this board.
3 <SDI 3 IN> terminal
This is a terminal to input SDI signal (SD-SDI/
HD-SDI/3G-SDI/6G-SDI/12G-SDI).
4 <SDI 4 IN/3 OUT> terminal
This is a terminal to input SDI signal (SD-SDI/HD-SDI/3G-SDI).
This is also an active through terminal to output the SDI signal
(SD-SDI/HD-SDI/3G-SDI/6G-SDI/12G-SDI) input to the <SDI 3
IN> terminal of this board.
5 Handle
Note
f
The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f
To use the <SDI 2 IN/1 OUT> terminal or the <SDI 4 IN/3 OUT> terminal as an output terminal, set the [DISPLAY OPTION] menu
→
[SLOT
IN]
→
[SDI MODE] to [OUTPUT].
f
When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
f
Install this board in either <SLOT 1> or <SLOT 2>. When these boards are installed in both <SLOT 1> and <SLOT 2>, only the board
installed in <SLOT 1> can be used.
r
Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10)
This board supports the DisplayPort signal.
1
3
3
2
1 <DisplayPort IN 1> terminal (when installed in <SLOT 1>),
<DisplayPort IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input DisplayPort signal.
2 <DisplayPort IN 2> terminal (when installed in <SLOT 1>),
<DisplayPort IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input DisplayPort signal.
3 Handle
Содержание PT-RQ35KU
Страница 61: ...ENGLISH 61 Chapter 3 Basic Operations This chapter describes basic operations to start with...
Страница 101: ...Chapter 4 Settings PICTURE menu ENGLISH 101 Note f f sRGB is available for RGB signal input only...
Страница 200: ...200 ENGLISH Chapter 5 Operations This chapter describes how to use each function...