Panasonic PT-RQ35KU, Руководство по эксплуатации

Страница: 277 / 291

Chapter 7 Appendix — Specifications
ENGLISH - 277
*6 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level. When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is
set to [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F),
regardless of the altitude. When the Smoke Cut Filter is used, the operating environment temperature should be between 0 °C (32 °F) and 40 °C
(104 °F).
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], the projector cannot be used at an altitude of 2 700 m (8 858') or higher above sea level. When the Smoke Cut Filter is used, the projector
cannot be used at an altitude of 1 400 m (4 593') or higher above sea level.
*7 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [HIGH] or [NORMAL], and the operating
environment temperature exceeds the following value, the light output may be reduced to protect the projector.
f
When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
f
When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], and the operating environment temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
Note
f
The light output will decrease to approximately 1/3 when using the projector with AC 100 V to AC 120 V.
f
The model numbers of accessories and optional accessories are subject to change without prior notice.
r
Connecting terminal/slot
<SDI IN 1> terminal
<SDI IN 2> terminal
<SDI IN 3> terminal
<SDI IN 4> terminal
Total 4 sets (BNC)
Single link SD-SDI signal SMPTE ST 259 compliant
Single link HD-SDI signal
SMPTE ST 292 compliant
Single link 3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI signal SMPTE ST 372 compliant
<SDI IN 1> terminal: LINK-A signal/<SDI IN 2> terminal: LINK-B
signal/<SDI IN 3> terminal: LINK-A signal/<SDI IN 4> terminal:
LINK-B signal
Dual link 3G-SDI signal SMPTE ST 425 compliant
<SDI IN 1> terminal: Link 1 signal/<SDI IN 2> terminal: Link 2
signal/<SDI IN 3> terminal: Link 1 signal/<SDI IN 4> terminal:
Link 2 signal
Quad link HD-SDI signal <SDI IN 1> terminal: Link 1 signal/<SDI IN 2> terminal: Link 2
signal/<SDI IN 3> terminal: Link 3 signal/<SDI IN 4> terminal:
Link 4 signal
Quad link 3G-SDI signal
SMPTE ST 425 compliant
<SDI IN 1> terminal: Link 1 signal/<SDI IN 2> terminal: Link 2
signal/<SDI IN 3> terminal: Link 3 signal/<SDI IN 4> terminal:
Link 4 signal
<MULTI PROJECTOR SYNC
IN> terminal
1 set (BNC)
TTL high impedance
<MULTI PROJECTOR SYNC
OUT> terminal
1 set (BNC)
TTL output: Maximum 10 mA
<SERIAL IN> terminal
<SERIAL OUT> terminal
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
<REMOTE 1 IN> terminal
<REMOTE 1 OUT> terminal
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
<REMOTE 2 IN> terminal 1 set, D-Sub 9 p, for contact control
<DIGITAL LINK/LAN> terminal
1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT
TM
compliant), PJLink compatible,
100Base-TX, Art-Net compatible, HDCP 2.2 compatible, Deep Color compatible
<SLOT 1>
<SLOT 2>
Total 2 sets (blank), SLOT NX specification, for installing the Interface Board
<DC OUT 1> terminal
<DC OUT 2> terminal
2 sets, USB connector (type A), for power supply only (DC 5 V, maximum 900 mA for each terminal)