T
ro
uble
s
ho
oting
VQT3C77
91
Messages on the unit’s display
Troubleshooting
The following messages or service numbers appear on the
unit’s display when something unusual is detected during
startup and use.
DVD
(“
∑
” stands for a
number.)
The remote control and main unit are
using different codes. Change the code
on the remote control. (
>
87)
CAM-UP
CAM is being updated. (
>
89)
GUIDE
TV Guide data is being downloaded.
(
>
26)
FINISH
The software (firmware) update is
complete. (
>
89)
HARD ERR
If there is no change after turning the unit
on and off, consult the dealer where the
unit was purchased.
NoERAS
You cannot delete items on this disc.
The disc may be damaged. Use a new
disc.
NoREAD
≥
The disc is dirty or badly scratched. The
unit cannot record, play, or edit. (
>
9)
≥
This message may appear when the
lens cleaner has finished cleaning.
Press [
<
OPEN/CLOSE] on the main
unit to eject the disc. (
>
18)
NoWRIT
You cannot write to this disc.
The disc may be damaged. Use a new
disc.
PLEASE
WAIT
≥
Displayed when the unit is started and
turned off.
≥
There was a power failure or the AC
plug was disconnected while the unit
was on. The unit is carrying out its
recovery process. This process
restores the unit to normal operation.
The unit is not broken. Wait until the
message disappears.
PROG FULL
There are already 64 timer programmes.
Delete unnecessary timer programmes.
(
>
35)
REMOVE
The USB device is drawing too much
power. Remove the USB device.
START
Update of the software (firmware) is
started.
You cannot operate the unit until the
update is complete. (
>
89)
SW-DL
Software (firmware) is downloading.
Download will stop when the unit is
turned on, or the timer recording starts.
(
>
89)
UNSUPPORT
You have inserted a disc the unit cannot
play or record on. (
>
6)
You tried to operate with a non-
compatible USB memory.
UPD
/
(“
∑
” stands for a
number.)
The software (firmware) is being
updated.
You cannot operate the unit until the
update is complete. (
>
89)
U59
The unit is hot.
The unit switches to standby for safety
reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation
when installing the unit. Do not block the
cooling fan on the rear of the unit.
U61
(When a disc is not inserted) Displays
when a malfunction has occurred. This is
displayed when the unit is in the recovery
process to return to normal operation.
Once the display clears you can use the
unit again.
If it remains displayed, consult the dealer
where the unit was purchased.
U76
HDMI cannot be output because it is
connected to a model that does not
support copyright protection.
U77
Due to the current disc not having
authorised copyright information, video
output is not performed.
U88
(When a disc is inserted) Displays when
there was something unusual detected
with the disc while recording, playback or
copy. This is displayed when the unit is in
the recovery process to return to normal
operation. Once the display clears you
can use the unit again.
If it remains displayed, consult the dealer
where the unit was purchased.
U99
The unit fails to operate properly. Press
[
Í
/I] on the main unit to switch the unit to
standby mode. Now press [
Í
/I] on the
main unit again to turn the unit on.
H
or F
(“
∑
” stands for a
number.)
≥
There is something unusual. (The
service number displayed after H and F
depends on the unit’s condition.)
≥
Check the unit using the
troubleshooting guide. (
>
92) If the
service number does not disappear, do
the following.
1. Disconnect the plug from the
household mains socket, wait a few
seconds, then reconnect it.
2. Press [
Í
/I] to turn the power on. (The
unit may be fixed.)
If the service number does not disappear
despite after doing the above, request
service from the dealer. Inform the dealer
of the service number when requesting
service.
X HOLD
The HOLD function is activated.
Press and hold [OK] and [RETURN
] at
the same time until “X HOLD”
disappears. (
>
18)
DMRXS400EG-VQT3C77_eng.book 91 ページ ２０１１年５月１６日 月曜日 午前９時３分
