Panasonic CS-RZ25TKR Скачать руководство пользователя страница 62

Страница: 62 / 196

12.2.4.1 Wire Stripping and Connecting Requirement

12.2.5 Cutting and Flaring the Piping

1 Please cut using pipe cutter and then remove the burrs.
2 Remove the burrs by using reamer. If burrs is not removed, gas leakage may be caused.

Turn the piping end down to avoid the metal powder entering the pipe.

3 Please make flare after inserting the flare nut onto the copper pipes.

WARNING

RISK OF FIRE

JOINING OF WIRES
MAY CAUSE
OVERHEATING
AND FIRE.

Use complete
wire without joining.

Use approved
socket and plug
with earth pin.

Wire connection
in this area must
follow to national

wiring rules.

Do not joint wires

Wire stripping

No loose strand

when inserted

10 ± 1 mm

5 mm or more

Indoor/outdoor connection
terminal board

(gap between wires)

Conductor

fully inserted

Conductor

over inserted

Conductor not

fully inserted

PROHIBITED

1. To cut

When properly flared, the internal surface of the
fl are will evenly shine and be of even thickness.
Since the flare part comes into contact with the
connections, carefully check the flare finish.

Improper fl aring

Inclined Surface

damaged

Cracked Uneven

thickness

3. To fl are

Bar

Red arrow mark

Handle

Core

Yoke

Clamp handle

Bar

0 – 0.5 mm

Copper
pipe

Reamer

2. To remove burrs

Point down

Pipe

Содержание CS-RZ25TKR





































































































































































































Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-RZ25TKR, Руководство по обслуживанию

Результаты поиска

Содержание CS-RZ25TKR

Отзывы:

Бренды по названию

Популярные бренды